answersLogoWhite

0

What else can I help you with?

Related Questions

How do you remove ac compressor on 2000 suzuki grand vitara?

Remove the drive belt from the air conditioner compressor. Remove the air conditioning hoses from the compressor. Remove the retaining bolts from the air conditioner compressor.


How do you remove the rear seats of a 2010 Suzuki Grand Vitara?

To remove the rear seats of a 2010 Suzuki Grand Vitara, start by folding down the seatbacks to access the mounting bolts. Use a socket wrench to remove the bolts securing the seat cushion and seatbacks to the floor and body of the vehicle. Once the bolts are removed, carefully lift the seat cushion and seatbacks out of the vehicle. Make sure to check for any additional clips or fasteners that may need to be disengaged during the process.


How do you change the water pump on a 2001 Suzuki XL7 Grand Vitara?

Remove the water return hose from your 2001 Suzuki water pump. Remove the water pump belt. Remove the water pump retaining bolts. Reverse the process to install your new water pump.


How do you remove alternator on 2000 suzuki vitara?

To remove the alternator from a 2000 Suzuki Vitara, first disconnect the negative battery terminal to ensure safety. Then, remove any engine covers if necessary, and locate the alternator. Loosen the serpentine belt tensioner to relieve tension on the belt, then remove the belt from the alternator. Finally, disconnect the electrical connectors and mounting bolts securing the alternator, and carefully remove it from the engine compartment.


On a 98 civic ex there's two bolts that go through the brake rotors do you have to remove them to take off the rotors?

There are not bolts going THROUGH the rotors. In order to remove the rotor you have to remove the caliber, that does have two slide pins holding it in place.


What socket fits the head bolts on a suzuki vitara?

The head bolts on a Suzuki Vitara typically require a 12-point socket, specifically a 10mm or 12mm size, depending on the engine variant. It's essential to confirm the specific model and year of the Vitara, as configurations may vary. Always refer to the vehicle's service manual for precise specifications and torque settings.


How do you replace rear exhaust suzuki vitara?

To replace the rear exhaust on a Suzuki Vitara, start by lifting the vehicle and securing it on jack stands. Remove the old exhaust by loosening the clamps and bolts that connect it to the exhaust system. Install the new rear exhaust by aligning it with the hangers and securing it in place with the clamps and bolts. Finally, check for any leaks and ensure everything is properly secured before lowering the vehicle.


How do you remove front rotors from 2004 suzuki aerio sx?

1. jack car and remove wheel 2. remove the brake caliper and pads by removing the two bolts holding on the caliper 3. remove the mounting bracket for the brake caliper by removing the two bolts attaching it to the spindle. 4. pull the rotor off


How do you remove the front brake rotors on a 2002 century?

there are two bolts that hold brake calipers to a u shaped bracket, remove them and then remove the two bolts holding the u shaped bracket. The rotors will come off at this point.


How do you replace Rotors on a 2001 Ford Expedition?

Remove wheels Remove 2 caliper mounting bolts Slide caliper off rotors Rotors should slide off hub


How do you remove the evaporator from suzuki vitara?

To remove the evaporator from a Suzuki Vitara, first ensure the vehicle is turned off and the battery is disconnected. Begin by removing the dashboard and any components obstructing access to the HVAC unit. Then, disconnect the refrigerant lines, electrical connectors, and any mounting bolts securing the evaporator. Finally, carefully extract the evaporator from the HVAC housing, taking care not to damage any surrounding components.


How do you get the front rotors off of a 2002 suzuki grand vitara?

After you have removed the calipers and brake pad bridge you need to use 2 8mm x 125 pitch bolts they need to be about 1 inch long screw them in to the holes that are provided screw them until they pop off