0
What else can I help you with?
What is the cement you need to use for chimneys?
Fire bricks or kiln bricks.Any grey cement will do.
How do you Calculate of cement thickness for cement lined pipes?
To calculate the cement thickness for cement-lined pipes, you first need to determine the pipe's diameter and the required cement lining thickness based on design specifications or standards. The typical formula is to consider the internal diameter of the pipe and subtract the desired thickness from it, ensuring that the cement layer meets or exceeds minimum thickness requirements for durability and corrosion resistance. Additionally, account for factors like pressure, temperature, and the specific application of the pipe to finalize the thickness. It's advisable to consult relevant engineering standards or guidelines for precise calculations.
How can you eliminate a hydrogen sulfide odor in the water from a new hot water heater even after the anode has been replaced with an aluminum one?
You need to replace the aluminum anode with a zinc/aluminum alloy anode.ANS 2 - If a hydrogen sulfide (or rotten egg) odour exists around your water, it's often an indicator of excess iron in the water supply. This can be bad for your plumbing. I would advise taking a water sample(in a sterilised bottle) to a lab and have it analysed. If the iron content is very high you may well have to fit a softener or an iron filter.BTW - changing the anode is an excellent idea anyway. Just may not be the solution.
Is PVC waterproof?
Yes.PVC stands for Polyvinyl chloride. It is water resistant and so it is waterproof.It is a synthetic resin prepared by the polymerization of vinyl chloride.PVC is used to make water pipes, floor sheets and tiles, water proof cartons, rain coats, shower curtains, and many items that need to be protected from water and fire.It is also flame resistant. Chlorine is released when you burn PVC, and chlorine atoms inhibit combustion.
Can you use white distilled vinegar to etch concrete?
Concrete is very hard. To do any good in etching it you need something very strong. Muriatic Acid is the only thing that I have found that works. How strong you mix it depends on the concrete. Some concrete that was poured with a lot of water in the mix will need less Acid. Concrete that is smooth and hard will take more. Muriatic Acid is caustic. Read the direction. Use rubber gloves; safety glasses; and a respirator. For a large project, such as a driveway or Patio. Use a plastic garbage can. Fill with 10 gallons of water. Carefully pour one gallon of Muriatic Acid into the water and mix with a wooden paddle. Take a plastic watering can and fill it with the solution. Wet your concrete with a water hose, then carefully pour the Acid solution onto the concrete. It will bubble and foam. This is the acid etching the concrete. Let it set for about 15 min. Scrub with a stiff push broom, and then rinse with a water hose. The acid will kill plants and grass. Steve Schillinger sds@knology.net = Safety Note = Make sure you put the water in the garbage can first--adding water to acid is a sure way to get splashed with concentrated acid.
Can you replace your underground water lines with new smaller lines so the cement doesn't need to be dug up?
Yes, but you may have low water pressure. The lines going from the pump or water system to your home need to be 3/4 inch. Any less and low water pressure is the result.
What do you need to make cement?
you mean concrete I think? you need cement, sand and water in a specific ratio.
How much sand cement and water needs 1M3 foamed concrete?
different density need different sand ,cement and water , cement and water is about 2:1 , details please visiti website:httP://www.foamed.com.cn
How is the cement bridge different from a bamboo bridge?
cement bridge needs water to get strenghtened bt whereas bamboo bridge does not need any water.
What are the Need of water supply in civil engineering?
For washing bricks,making cement,
How can I create a cement water fountain for my garden?
To create a cement water fountain for your garden, you will need to build a mold using wood or other materials, mix cement with water to the desired consistency, pour the cement into the mold, and allow it to set and cure. Once the cement has hardened, remove the mold and add a water pump and tubing to create the fountain effect. You can also add decorative elements like stones or tiles to customize the fountain to your liking.
Are you required to have a special license or permit to drive a cement truck?
To drive a cement truck legally, you need a class B CDL (Commercial Drivers License). At 18, you can apply for a class B CDL.
How to do scale models and maps?
The scale on a map or blueprint is a ratio. Ingredients sometimes need to be mixed using ratios such as the ratio of water to cement mix when making cement.
How can I make a cement planter?
To make a cement planter, you will need cement mix, a mold, water, and a stirring tool. First, mix the cement with water according to the instructions on the package. Then, pour the mixture into the mold and let it set for at least 24 hours. Once the cement has hardened, remove the planter from the mold and let it cure for a few more days before planting anything in it.
How can I create cement garden ornaments?
To create cement garden ornaments, you will need cement mix, molds, water, a mixing container, and a stirring tool. First, mix the cement with water according to the instructions on the package. Then, pour the mixture into the molds and let it set for the recommended time. Once the cement has hardened, carefully remove the ornaments from the molds and allow them to fully cure before placing them in your garden.
How do you remove fuel lines from a Ford F-150?
You need a special tool available at lordco.
How can I create a cement mold DIY project?
To create a cement mold DIY project, you will need a mold, cement mix, water, mixing tools, and a release agent. First, prepare the mold by applying the release agent to prevent sticking. Then, mix the cement with water according to the instructions on the package. Pour the cement into the mold and smooth the surface. Allow the cement to cure for the recommended time before removing it from the mold. You can customize your project by adding color or decorations to the cement mix before pouring.
