0
On some of them, you may need silicone to seal the lowest seam. Depends on the design of shower base.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Mustee Shower Base?
form_title= Mustee Shower Base form_header= Enjoy showering with a Mustee shower base. Do you need to remove an old shower?*= () Yes () No Are you redoing the entire bathroom?*= () Yes () No Do you want the shower base delivered?*= () Yes () No
Do you need any type of glue when installing a gasket on a urinal?
No, you don't if the gasket is rubber.
Does a shower need a trap beneatrh base?
YES, it definitely does.
When installing a shower drain in a concrete floor how do you determine the height of the drain which will protrude through the concrete?
First determine what you are going to install as the shower unit. If there is to be no shower unit and it will just drain through the concrete floor, then it will be flush with the floor. If you are installing a unit, then you need to look at the unit to determine the distance obove the concrete to place the drain.
Installing A Shower Unit?
How to install a shower unitHomeowners who want to install a shower in their home can do the job themselves instead of having to pay someone to do it. Find the materials that you need to complete the shower. You will need the base for the shower, the shower door, fiberglass for the shower itself, and the attachments. Begin by building the base of the shower. Make the base tall enough to keep the water off the floor, but low enough so you can easily step over the edge to get in the shower. Construct the frame of the shower from the wood and then add the fiberglass to the wooden frame. Use caution when using fiberglass because you can get the small glass particles in your hands.Make a door frame that will house the shower door. When you finish with the frame, carefully slide the glass form the packaging into the frame. Use brackets to attach the hinges so that the door will open and shut. Make sure the door closes completely so no water leaks out of the shower. Install the plumbing attachments so you can take a shower as well as any extras you would like in the shower such as towel racks and containers for shampoo.
Can you install a walk in shower without hiring a professional?
Walk in shower stalls are moderately difficult to install. Pre fab shower stalls are already built for you and only need to be installed. Unless you are an expert it is highly recommended to hire a licensed plumber to get the plumbing set up before installing your shower.
How do you increase water pressure at shower head when the pressure below is great?
If it is a gravity fed shower raise the tank or use a shower pump in the loft. If its off a combi boiler you cant without butting a bigger out put boiler in. If its a electric shower put a higher kw shower in (may need lager wire installing). or simple descale you're shower head.
I will be installing travertine stone tiles in my foyer. It has a concrete slab as a base. Do I need to seal it before I adhere the stone to it If so what is the best product for this application ?
You should use a shower pan liner kit for this installation. The liner in most kits kit was made of rubberized asphalt laminated to a reinforcement fabric.
Do drip irrigation systems need glue to be assembled?
Depends on the fittings. Some types will need glue, others can be push type which dont need glue.
When installing a sewage basin and pump it is understand that the basin itself needs to be vented What about the toilet shower and sink that it will service do they need to be vented as well?
Yes. Toilet, shower, sink, or any other fixture that you might have needs to have a vent. Why? --->>> Toilet, shower or sinks are all independent fixtures where they all individually need air in order to flow properly. Any of these fixtures will not take air from the same vent you have at the basin.
Do you need a hot glue gun to melt hot glue sticks?
Yes, you do need a hot glue gun, it's the only safe way.
What do you use to glue shower liner together?
If you are referring to shower surround that will depend on what it is made out of and what you mean when you say "glue it together". Mastik or construction adhesive would probably be used to secure it to the wall. In some cases, thin set might be used. Silicone, epoxy, or grout would be used to fill the seams. What you use will depend on what it's made out of. If you read the installation instructions will probably tell what you need to use.
