0
I WILL ASSUME THIS IS NOT A POORLY INSULATED LEAKY HOME, IN THAT FREQUENT CYCLING OF EQUIPMENT IN THE AFOREMENTIONED BUILDING WOULD BE NORMAL. 1) CHECK THAT THE CAVITY BEHIND THE THERMOSTAT IS SEALED, WHERE THE WIRING COMES THROUGH THE WALL. (DRAFTS OF THIS KIND CAN CAUSE THIS SYMPTOM) 2) CHECK THE HEAT ANTICIPATOR ADJUSTMENT ON THE THERMOSTAT ITSELF. IT SHOULD CLOSELY MATCH THE CURREND DRAW (IN AMPS) OF THE FURNACE LOADS DURING THE HEATING CYCLE WITH THE BURNER OPERATING. IF YOU HAVE AN AC AMMETER, YOU SIMPLY PUT IT IN SERIES WITH THE "W" WIRE, AT THE FURNACE MAY BE EASIER THAN AT THE T-STAT ITSELF. THE ANTICIPATOR SHOULD BE ADJUSTED TO THE MEASURED METER READING. (BETWEEN 0.2 AND 1.2 AMPS NORMALLY). IF NO METER IS AVAILABLE, SIMPLY INCREASE THE ADJUSTMENT SAY 0.2 AMPS FROM WHERE IT IS SET NOW AND CHECK OPERATION. MANY ARE LABELED "LONGER" WITH AN ARROW POINTING IN THE DIRECTION OF INCREASED AMPERAGE. MANY ELECTRONIC STATS HAVE DIP SWITCHES ALLOWING YOU TO CHANGE THE CPH. (CYCLES PER HOUR) lc
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you turn furnace on without thermostat?
turn breaker off. unhook thermostat wire to furnace turn breaker on. worth a try; if it works you will have to turn off breaker to shut it down.
How can you test thermostat in your furnace?
Set thermostat to desired temperature; lets say, 70 degrees Fahrenheit, a few seconds will go by then the furnace should activate. Once the furnace heats the room to the set temperature the furnace should shut off.
How is your endocrine system like the thermostat in your house?
The negative feedback system. It works much the way a thermostat works. When the temperature in a room drops below a set level, the thermostat signals the furnace to turn on. Once the furnace has raised the temp in the room to the set level, the thermostat signals the furnace to shut off. It will continue to stay off until the thermostat signals that the temp has dropped again.
Why wont your electric furnace shut off?
Your thermostat might be shorted out. Remove one of the wires off of the stat to see if the furnace will shut down that way.
Why was power lost to a heat and air thermostat?
The power to the thermostat comes from the transformer in the furnace or air handler whichever you have. 1) the power to the furnace/AH is off, 2) the control fuse that protects the transformer is blown, 3) the transformer is defective, 4) the wire between the furnace and the thermostat got cut.
What is wrong if you turn the thermostat to off but the furnace is still running?
When you say the furnace is still running, I take that to mean the fan and not the actual flame portion of the furnace. If this is correct, you either have a fan relay that is sticking closed or your tstat is bad. == == == == There may be a very slight time delay the the thermostat before turning off the furnace, but if you are sure that you have turned the thermostat off and the fire continues to burn, you have a serious problem. Have it checked out. The gas valve may be sticking in the open position. Regards
How do you know if you need to replace your home thermostat?
Well, I don't mean to sound snarky, but when it doesn't work anymore! The thermostat, in its most basic form, is just a switch to turn the heater on. If the heater turns on and off like it should, it is OK. If the heater doesn't turn on, or worse yet doesn't turn off, you should look into getting a new one. Some tests you can perform: Heater doesn't turn on? Get at the wires running to the thermostat and touch the two control wires (You will have to look into the furnace documentation if you have more than two wires) together. If the furnace clicks on, it's the thermostat. If it doesn't, it's the furnace. Heater doesn't turn off? When the furnace is running disconnect one of the control wires. If the furnace shuts off it's the thermostat. If it doesn't, it's the furnace.
How do you know if you need to replace your thermostat?
Well, I don't mean to sound snarky, but when it doesn't work anymore! The thermostat, in its most basic form, is just a switch to turn the heater on. If the heater turns on and off like it should, it is OK. If the heater doesn't turn on, or worse yet doesn't turn off, you should look into getting a new one. Some tests you can perform: Heater doesn't turn on? Get at the wires running to the thermostat and touch the two control wires (You will have to look into the furnace documentation if you have more than two wires) together. If the furnace clicks on, it's the thermostat. If it doesn't, it's the furnace. Heater doesn't turn off? When the furnace is running disconnect one of the control wires. If the furnace shuts off it's the thermostat. If it doesn't, it's the furnace.
How does a thermostat extinguish or light a furnace?
It sends an electric signal to the valve to tell it to turn on or off.
Device for regulating furance heat?
A device for regulating furnace heat is the thermostat. A programmable thermostat can be set to control the temperature inside the home on a regular schedule. The thermostat is set to a desired temperature and then the furnace turns on and off to accomplish the desired heat level.
Device for regulating furnace heat?
thermostat is commonly used to regulate the heat of a furnace. It can programmed to maintain a desired temperature by turning the furnace on or off as needed. Some thermostats have additional features such WiFi connectivity, smart home integration, and scheduling options.
Is your furnace thermostat bad well the furnace dont stay on long it stays on for 45 seconds to a minute then kicks off for about five minutes is my thermostat bad?
Furnaces that cycle on and off frequently like yours does can have a few possible reasons that may or may not be part of the thermostat. A digital thermostat may not be the reason, but an old thermostat with a mercury switch inside which moves when the bimetal strip heats and cools down is a possibility. If the thermostat has an electrical problem (only 24 volts) could be causing the bimetal strip heat up fast, simulating the room getting warm. Another possibility is inside the furnace heat exchanger area. There is a safety device which turns off the furnace and fan when it gets hotter than it is supposed to, so you don't burn down your building. (this supposes that you have a forced air furnace which you did not mention or not) If you have a wall heater, it has a similar type of high temperature cut out. These temperature cut out devices are not very expensive and can be replaced fairly easily. Have someone just check the wiring of the thermostat by unscrewing it from the wall to see if there are any problems with the wires as well as verifying that it is or is not a mercury bulb controlled device.
