0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are the advantages and dis advantage of full-wave bridge rectifier compared with two diodes rectifier?
in full wave bridge rectifier, the input and out put voltages are same but in case of two diode rectifier the input and output voltages can be different as per requirement a there is a transformer in the circuit. The former is lighter and the later is heavier.
What is the relationship of the input frequency and output frequency in a FULL-wave rectifier?
The frequency of a full-wave rectifier is double that of the input, if the input is a sine wave or triangle wave. If the input is a square wave, the output is DC. If the input is a sawtooth wave, the output is a triangle wave of the same frequency.
Why a full wave rectifier is preferred over a half wave rectifier?
The a.c. component, or ripple, produced by the 4-diode (full wave) bridge rectifier is the same as that produced by the 2-diode full wave rectifier. The bridge is connected across the secondary winding of a transformer. The 2 diodes of the other type of full wave rectifier are each connected to one end of a winding, but that winding requires a center tap. For any desired value of d.c. after rectification, the a.c. voltage of the 2-diode rectifier winding has to be twice that of the winding required for the bridge.
What is the difference between a one diode rectifier and a two diode rectifier?
A one diode rectifier is called a half wave rectifier and only allows current flow for the positive portion of the sine wave. A two diode rectifier, or full wave rectifier allows positive current flow during the positive portion of the wave as well as positive current flow during the negative portion of the sine wave. This results in a much cleaner DC power signal. The addition of a capacitor in the output circuit will clean up the signal very nicely.
Is it necessary for 2 diodes of full wave rectifier to be identical?
It is not really necessary for 2 diodes of full wave rectifier to be identical. However, it must be understood that the two diodes will have the same forward current, and the same reverse voltage, applied to them, so their ratings should be comparable.
Types of rectifier?
There are basically two types of rectifiers one is the half wave rectifier and the other is the full wave rectifies. The full wave rectifier is further classified into two types namely the bridge rectifier and the center tapped rectifier.There are also silicon controlled rectifiers nowadays.
What are the advantages and dis advantage of full-wave bridge rectifier compared with two diodes rectifier?
in full wave bridge rectifier, the input and out put voltages are same but in case of two diode rectifier the input and output voltages can be different as per requirement a there is a transformer in the circuit. The former is lighter and the later is heavier.
What is the relationship of the input frequency and output frequency in a FULL-wave rectifier?
The frequency of a full-wave rectifier is double that of the input, if the input is a sine wave or triangle wave. If the input is a square wave, the output is DC. If the input is a sawtooth wave, the output is a triangle wave of the same frequency.
Full wave rectifier using RC triggering circuit with diagram?
A full-wave rectifier (sometimes called a "bridge" rectifier) produces output current on both half-cycles of the input AC waveform. ******************************************** There are two types of full wave rectifier circuit. One uses four diodes in a "bridge"configuration and is fed from a simple transformer winding. The other uses two diodes and needs to be fed from a centre tapped transformer winding.
Why a full wave rectifier is preferred over a half wave rectifier?
The a.c. component, or ripple, produced by the 4-diode (full wave) bridge rectifier is the same as that produced by the 2-diode full wave rectifier. The bridge is connected across the secondary winding of a transformer. The 2 diodes of the other type of full wave rectifier are each connected to one end of a winding, but that winding requires a center tap. For any desired value of d.c. after rectification, the a.c. voltage of the 2-diode rectifier winding has to be twice that of the winding required for the bridge.
What is the main difference between a bridge rectifier and a full wave rectifier?
Both the bridge rectifier and the full-wave rectifier achieve the same thing. They rectify the AC input on both opposing phases so as to minimize ripple time and voltage. The difference is that a bridge rectifier consists of four diodes arranged in a bridge, so the input needs to only be single phase AC, while a full wave rectifier consists of two diodes, but needs a split phase AC source, such as provided by a center tapped transformer winding. Also, the bridge rectifier presents two junction drops in the output, because there are always two diodes in series, while the full-wave rectifier presents only one junction drop in the output, because there is only one. It is a trade-off.
What is the difference between a one diode rectifier and a two diode rectifier?
A one diode rectifier is called a half wave rectifier and only allows current flow for the positive portion of the sine wave. A two diode rectifier, or full wave rectifier allows positive current flow during the positive portion of the wave as well as positive current flow during the negative portion of the sine wave. This results in a much cleaner DC power signal. The addition of a capacitor in the output circuit will clean up the signal very nicely.
What is need of rectifier in electronics?
rectifiers are used in electronics to convert the sine wave into its +ev side only.there are two rectifiers half wave and full wave rectifier half wave take +ev of only one cycle and full wave rectifies whole cycle to its +ve.
Is 2 diode without center taped can befull wave rectifier?
No. For a full wave rectifier, you need two diodes and a center tapped secondary, or you need four diodes and a non-center tapped secondary.
Why three-phase rectifier is preferred upon single-phase rectifier?
The choice of single or three phase depends on the available supply. But a three-phase full wave rectifier provides 6 pulses of DC per cycle, while a single-phase full-wave rectifier provides only two. That makes the output DC easier to smooth.
Why you are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?
If diode in the bridge circuit becomes open the circuit will become a half wave rectifier instead, but if a diode in a full wave rectifier opens then the whole circuit becomes open. (No current flow). ************************************************************** The outputs of the bridge and the two-diode full wave rectifier are not the same. For the rectified voltage to be the same value, the two-diode full wave rectifier must be supplied from a centre tapped transformer winding, the total voltage of which is twice that necessary for the bridge rectifier circuit. Furthermore, the maximum d.c. which may be drawn from the centre tapped transformer/two-diode arrangement, assuming capacitive filtering, is the same value as the transformer secondary winding's capacity. In the case of the bridge, the maximum d.c. which may be drawn, also assuming capacitive filtering, is 62% of the transformer secondary winding's capacity.
Is it necessary for 2 diodes of full wave rectifier to be identical?
It is not really necessary for 2 diodes of full wave rectifier to be identical. However, it must be understood that the two diodes will have the same forward current, and the same reverse voltage, applied to them, so their ratings should be comparable.
