0
If the wire is soild and circular with a 5 mm diameter, the cross-section area is given by the formula for a circle, which is A = pi/4 x (diameter)2. For 5mm that is pi/4 times 25 or 19.73 square mm.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is the maximum current that can flow through a 5mm LED?
There are numerous 5mm LED manufacturors and they can have different specs. Consult the specification sheet for the component in question.The 500TSW4DF Super Bright White 5mm LED has a max forward current rating of 30mA on its spec sheet.The RL5-R8030 - Super-Red LED has a rating of 20mA
What is a fuse T5AL?
A T5AL is a tubular 5 amp 20mm x 5mm Slow Blow Anti Surge glass fuse.
What is the weight of 8mm thick chequered plate?
5mm thick chequered plate weiht per square metre
How to calculate press machine tonnage?
Well, First get the Dia of material in inches = A Get the thickness of material in inches = B Now, Multiplier for M.s is 80 & for soft material like copper, brass, alluminium is 6 0. now put the A X B X MULTIPLIER = TONNAGE Example, 1 inch dia 5mm thickness Material is M.S. SO TONNAGE is : 1 x 0.1968 x 80 = 15.75 is tonnage required... ENJOY TONNAGE FORMULA.
How do you turn a bar on a center lathe?
The basics procedure used for turning a bushing on lathe are:Material is inserted and tightened into the chuck so it protrudes about 10mm over the actual length of the final bushing lengthIf the material is not hollow bar, a drill is inserted into the tail stock then the material is drilled to enable the a boring bar to fit the holeA roughing tool is inserted into the tool post then the face of the workpiece is machined smooth and the outside diameter to about 0.5mm oversizeA roughing boring bar is inserted into the tool post and the inside diameter is machined to roughly 0.5mm undersizeA finishing tool is then inserted into the tool post then first the face and then the outside diameter of the workpiece is machined to the required sizeAt this point a finishing boring bar is inserted into the tool post and the inside diameter is machined to the required sizeChamfer tools are then used to chamfer both outside and inside edges at the faceThe parting tool is inserted into the tool post then the bushing is parted off about 0.5mm to 1mm longer than specified.The remainder of the material is removed from the chuck then the parted bushing is inserted and tightened with the unfinished side protruding about 5mm to 10 mm.A finishing tool is inserted into the tool post then the face is machined to the required sizeChamfer tools are then used to chamfer both outside and inside edges at the faceThe above method is just a basic explanation of how the operation is achieved. Operating a lathe without proper training is not recommended and could lead to serious injury!
What is the size of electric cable needed for a ring main circuit in a house?
it is 5mm
What is the diameter of the pencil you have?
5mm
What is the diameter of a pea?
5mm.
What is the diameter of a watch battery?
5mm
What is the circumference of a circle if the diameter is 2 5mm?
If the diameter is 25 mm then the circumference is 78.54 mm.
What is the diameter of a pencil?
pencils can have differend diameters,regular its about 5mm
What is the diameter of the normal carotid artery?
What is the diameter of the normal carotid artery?
Calculate 125mm x 125mm x 5mm?
125mm
What is an ice pellet larger than 5mm in diameter that forms during a thunderstorm?
sleet
What is the radius of a 5mm in diameter circle?
The radius would be 2.5 mm.
How you calculate weight of acrylic sheet eg 5mm perspex?
540x540x3 mm
What does 5mm look like in size on a ring band?
5 mm is about 1/5". About the diameter of a pea.
