Chrysler Town and Country

How do you change the map light bulb on a Chrysler?

129130131

Top Answer
User Avatar
Wiki User
2015-07-15 18:22:25
2015-07-15 18:22:25

Depending on the year and model/trim of your car, there are two possibilities here.

If the information console (the overhead console in which the map light is located) does NOT have a built-in garage door opener, then you can simply grab the front end of the console, and pull down. This will remove the console, and expose the light bulbs which can easily be replaced.

If the console DOES have a built-in garage door opener, then you must locate a small screw that is towards the windshield. Use a Phillips head screwdriver to remove the screw, and then pull off the faceplate to expose the bulbs.

Whatever you do, NEVER use a flat head screwdriver to pry the console off. Use your hands only. Using screwdrivers just gouges the plastic or tears the head-liner on your car, and makes it look like a botched job.

This is the correct protocal for a 2000 300M.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

light bulb out on map light how to change with out breaking plastic lens

User Avatar

You can replace the map light bald, on your Chrysler 300, by removing the decorative retaining nut. The lens will come off with the nut, exposing the light bulb.

User Avatar

The map light on a 2004 Dodge Grand Caravan SXT is changed gently prying the edge of the cover to reveal the bulb. The bulb can then be popped out and a new bulb installed.

User Avatar

how to replace map light bulb in a 2006 pontiac torrent

User Avatar

Just pop off the plastic lens... easiest if you pry from the middle.

User Avatar

To replace a light bulb in the map light on a 1996 Toyota Camry, the lens for the light has to be removed. There are clips at two opposite ends that have to be nudged gently with a flat screwdriver to get the lens cover off.

User Avatar

Remove the map light retaining ring. Remove the map light cover. Take hold of the lightbulb, push in and turn at the same time. The lightbulb will come out.

User Avatar

It doesn't have a dome light... it's a map light, #105

User Avatar

Just take the cover off and plug in the new bulb.

User Avatar

2005 Chevrolet Cobalt Light Bulb Replacement GuideHigh & Low Beam Headlamp Light Bulb Size:9007LLParking Light Bulb Size:3157LLFront Turn Signal Light Bulb Size:3157LLRear Turn Signal Light Bulb Size:3057LLTail Light Bulb Size:3057LLStop Light Bulb Size:3057LLHigh Mount Stop Light Bulb Size:912Fog/Driving Light Bulb Size:H11-55WLicense Plate Light Bulb Size:194Back Up Light Bulb Size:921Front Sidemarker Light Bulb Size:194Rear Sidemarker Light Bulb Size:194Map Light Bulb Size:2825LLDome Light Bulb Size:562Step/Courtesy Light Bulb Size:212-2

User Avatar

Since you didn't specify which bulb here is the entire list: Low beam headlamp Light Bulb Size: H1-55W High beam headlamp Light Bulb Size: H1-55W Parking Light Bulb Size: 2357A Front turn signal Light Bulb Size: 2357A Rear turn signal Light Bulb Size: 992 (7440A) Tail Light Bulb Size: 7443 Stop Light Bulb Size: 7443 High mount stop Light Bulb Size: 7440 Fog/Driving Light Bulb Size: H11-55W License plate Light Bulb Size: 2825 Back up Light Bulb Size: 921 Front sidemarker Light Bulb Size: 2825 Map Light Bulb Size: 2825 Dome Light Bulb Size: 2825 Step/Courtesy Light Bulb Size: 2825

User Avatar

how do i change the bulb in the clock on 2004 lincoln town car

User Avatar

Pry at the base (from the rear) of the map light cover. There are 2 slots in back that when pryed gently with a screwdriver; will allow you to pull the whole cover forward into your hands. When you are done replacing blubs just pop it back into place.

User Avatar

Just did that tonight. Mine has map lights in the middle position. Figure out where the hinge is, and gently pry at that point.

User Avatar

im trying to find the same on ethis is the best i could do Low Beam Headlamp Light Bulb Size: H4703 High Beam Headlamp Light Bulb Size: H4701 Parking Light Bulb Size: 3157A Front Turn Signal Light Bulb Size: 3157A Rear Turn Signal Light Bulb Size: 2057 or 3057 Tail Light Bulb Size: 194 or 2057 or 3057 Stop Light Bulb Size: 2057 or 3057 High Mount Stop Light Bulb Size: 921 Fog/Driving Light Bulb Size: 880 License Plate Light Bulb Size: 194 Back Up Light Bulb Size: 1156 Front Side Marker Light Bulb Size: 194 Rear Side Marker Light Bulb Size: 194 Glove Box Light Bulb Size: 194 Map Light Bulb Size: 214-2 Dome Light Bulb Size: 214-2 or 561 Step/Courtesy Light Bulb Size: 194 or 214-2 or 74 Trunk/Cargo Area Light Bulb Size: 561 Instrument-General Light Bulb Size: 161 or 37 or PC74 Check Engine Indicator Light Bulb Size: PC74 Hi-Beam Indicator Light Bulb Size: PC74 Seat Belt Indicator Light Bulb Size: PC74 Brake Warning Light Bulb Size: PC74 Automatic Transmission Indicator Light Bulb Size: PC74 Directional Signal Indicator Light Bulb Size: 161

User Avatar

The original is a #192, but is no longer available. Suggested use is a #194

User Avatar

use a tiny screwdriver to pop off the plastic piece that you push to turn the light on, then the bulb just pops out 1. Find the "hinged" side of the plastic light cover (the side that doesn't go up and down.) 2. Insert the tip of a flat-head screw-driver between the plastic light cover and the surrounding frame. The tip should be on the side of the hinge, about 1/4" away from either corner. The cover will pop right out. 3. Use your screwdriver to pop out the light bulb. My EX-L required a 12V-8A bulb. Easy!

User Avatar

To change the map light in a 2005 Town and Country, first lower the sunglass holder. Remove the single screw holding the console and firmly pull down the entire console from the rear. It will release the two clips allowing the entire console to be removed and the map light can be changed.

User Avatar

It is really simple. All you have to do is remove the plastic cover for the map light and the bulb is right there. If you put a screwdrive in the middle side fo the clear cover you can pry the cover off and have access to the light. The cover is made to be removed this way so don't use excessive pressure or you might break it.

User Avatar

the front maplight lenses come off with a small screwdriver just pry them off and put in a new bulb and pop the lens back on

User Avatar

You have to pop off the small plastic light cover on the mirror. Now either take a set of needle nose pliers and rubber gloves around them, or just try the rubber gloves. And apply pressure around the bulb and pull-out. Now just insert new bulb.

User Avatar

Answerfirst remove the light cover then just twist the bulb and it should come right off.^^ this info is wrong. You'll damage the socket if you twist the bulb. You need to pull the bulb out; it takes a bit of work, I managed to do it with a pair of pliars being very careful not to break the bulb itself (if you did I don't suppose it would be a problem since you're replacing it anyway). Then, you just pop in the replacement bulb and replace the cover. I did it on my 2001 camaro, though I can't imagine the 2000 being much different.

User Avatar

You are in luck, I just finished doing that this afternoon. You must remove the entire upper console. Theere is one screw in the from, right above the rear mirror assembly. Once you remove that, simply slide the entire console forward until it releases. There will be one red electrical connection that will need to be disconnected. Turn the console over and remove the map light assembly, remove lense and change bulb.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.