Here is a basic overview of the configuration of RIP on a Cisco router:
Router(config)#router rip
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.2.0
Router(config-router)#network 192.168.3.0
Router(config-router)#network 192.168.4.0
Router(config-router)#network 192.168.5.0
The 192.168.x.0 address can be changed to whatever address you would like to be broadcast over RIP. There are also other settings that can be configured.
If you use RIPv2 you can also have the following configuration:
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.2.0
Router(config-router)#network 192.168.3.0
Router(config-router)#network 192.168.4.0
Router(config-router)#network 192.168.5.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.You can configure multiple static routes. On a Cisco router, you would give several ip route commands. However, if there are a lot of routes to configure, it is more practical to use a routing protocol - that way, the routers learn available routes automatically.
First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.
Configure two interfaces, and build the routing table accordingly with their private IPS.
CDP
Enhanced Interior Gateway Routing Protocol (EIGRP) was once as Cisco Propitiatory routing protocol for Cisco routers. However many routers that are not Cisco now support the use of EIGRP.
EIGRP
On a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routingOn a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routingOn a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routingOn a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routing
HDLC
this is a cisco propreitory protocol is not available for rfc
Some recommended books about Cisco routers are: Cisco Router Configuration, Cisco Routers For The Desperate, Cisco Routers for IP Router, Cisco CCNA Routing and Switching.
IGRP is Interior Gateway Routing Protocol, enhanced by Cisco proprietary Enhanced IGRP.
You can do this on the enable, or privileged, prompt.