0
How do you disconnect a light switch and outlet that are tied together?
Wiki User
∙ 12y ago
If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.
Wiki User
∙ 12y ago
Wiki User
∙ 11y agoIf the switch just controls the outlet you would remove the switch and just wirenut the wires that went to each side of the switch together. Put a blank switch plate to cover the box. If the switch controls outlet and something else you need to determine if there is a seperate direct connection to each and then remove the outlet connection and wirenut the black lead to the outlet directly to the black lead on the supply side of the switch.
Add your answer:
Earn +20 pts
What is the difference between single pole switch and a three way?
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
How do you know which outlet is controlled by a switch?
Plug a lamp into a working socket of an outlet to ensure the lamp works. Then turn off the switch and plug lamp into all outlet sockets, top and bottom outlets until the lamp doesn't light. Then turn on the switch and the lamp should light. Often a switch in a bedroom is only connected to one socket in a duplex outlet. It is possible to remove a jumper in an outlet to isolate the sockets for just this purpose. Often an electrician will install the outlet upside down (The third prong pointing up, to identify the outlet.
Why is there no power to outlet when light switch is turned off?
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
How do you wire multilple power outlets and light?
Power into the first outlet and out to all other outlets, black to gold and white to silver screw, ground wires to ground screw. From the outlet closest to the light switch run power from that outlet up to the switch box. Run another wire from the switch box up to the light. In the switch box tie all the whites together under a wire nut and push them back into the box. Tie all the ground wires together and connect that to the ground screw on the switch. Connect the 2 black wires you have left to the 2 screws on the switch. Does not matter which if you only have power in and power out to the light.
How do you wire a light to a switch at the end of a run and which controls an outlet?
Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.
Does an outlet controlled by a light switch still pull energy when the light switch is off?
No.
Why does the light switch not work to an existing electrical outlet?
Could be a loose connection somewhere, or a bad switch, or a bad outlet.
Can you change an electrical outlet into a switch for a light?
Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.
What is the difference between single pole switch and a three way?
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
Have a wall outlet that when you turn the light switch on the outlet has no power need help?
Change the wall outlets
How do you replace the backup light switch for 1990 Mazda Miata?
The backup light switch is located on the left side of the transmission. Disconnect the switch connectors, then unscrew the switch.
You want to disconnect your outdoor lighting that is on a movement sensor to just a regular offon type switch how do you do that?
There should be a switch on the light itself to disconnect the sensor.
How do you wire one light and one GFCI and another light light and fan with two switches and one power line?
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
How do you wire a two way switch one controls the outlet the other the outdoor light with a pigtail?
You need two separate switches. You can get two switches that are in the same form factor as a single switch (2 gang switch). You use one switch for the outlet and the other for the light. You switch the black wires which are "hot".
How do you know which outlet is controlled by a switch?
Plug a lamp into a working socket of an outlet to ensure the lamp works. Then turn off the switch and plug lamp into all outlet sockets, top and bottom outlets until the lamp doesn't light. Then turn on the switch and the lamp should light. Often a switch in a bedroom is only connected to one socket in a duplex outlet. It is possible to remove a jumper in an outlet to isolate the sockets for just this purpose. Often an electrician will install the outlet upside down (The third prong pointing up, to identify the outlet.
Why is there no power to outlet when light switch is turned off?
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
How can you make music come on with a light switch?
You can make music come on with a light switch the same way you can make a light bulb come on - plug a radio into the switched outlet.
