0
You can take a big pair of channellock pliers and squeeze it back together then take some ruby fluid clean it the solder with 15% silversolder. Use Mapp or Acetalene gas or you'll be there forever. Put something over your nose cause its going to stink.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the right connection fitting for a 2 inch PVC shower drain and trap to a 2 inch copper drain pipe?
A fernco or rubber fitting. This made of rubber and had hose clamps on it. You should ask for assistance at a hardware or plumbing shop for a 2" Plastic X 2" Copper Fernco or rubber coupling.
How do you install sewage under a modular home?
There will be the connection to the sewer and the drain coming out of the house. Connect the two with PVC at the proper pitch. 1/8 inch fall per foot of length.
How big is a sewer rod?
A sewer "rod" is normally no larger then 3/8 of an inch diameter BUT a SEWER Cable can be as large as 11\4" even the small sewer rods can have large heads to maintain sewers as large as 36"
What is the minimum fall for a 4 inch sewer pipe?
1/8" per foot.
Can you use a 3 inch pipe as sewer line?
In Tulsa Oklahoma you can, but i would still use 4 in.
What is the Level of drop for sewer drain?
1/8 inch per foot
How do you tie water softner into septic line?
You must first connect a 1/2 inch PVC pipe to the outlet for the regeneration fitting on the softner and run this pipe outside and trench to the sewer drain and tie into sewer drain. The sewer drain will then flow the brine regenerater fluid to the septic tank.
What slope to use on sewer drain lines?
One eighth inch drop per foot of run.
Is 4 inch the standard size for drain pipe to sewer?
Depends on locality as many of the one family homes require I install sewer mains from 4" - 6". The size of the "sewer" is based on fixtures units that are connected and to local codes
How do you figure the pitch for a new drain for a washer with a length of approx 50 feet to sewer hub?
The building code where I live requires a drain pipe to slope approximately 1/4 inch per foot (+ or - 1/8 inch). The recommended pitch for a 50 foot drain would be 12-1/2 inches.
How do you install an indirect drain to the main system to prevent possible sewage back-up into a 3 compartment sink?
You must maintain a 2" air gap from indirect waste to sewer waste. If sewage back up was the issue, I would recomend "directly" piping the 2 inch drain to the main sewage with a 2 inch normally closed backwater valve. If you piped an indirect drain you would not be protected from sewer back up. I assume this is for a sink perhaps in a basement?
What is the right connection fitting for a 2 inch PVC shower drain and trap to a 2 inch copper drain pipe?
A fernco or rubber fitting. This made of rubber and had hose clamps on it. You should ask for assistance at a hardware or plumbing shop for a 2" Plastic X 2" Copper Fernco or rubber coupling.
How do you install sewage under a modular home?
There will be the connection to the sewer and the drain coming out of the house. Connect the two with PVC at the proper pitch. 1/8 inch fall per foot of length.
What is the maximum slope for 4 inch sewer pipe?
1/8th per inch
How long should a 3 inch copper drain line last?
1- What type of waste is the coper being used for (acidic ) 2- What type of "copper" Type K, L , M , DWV, Copper tubing can last less then 2 weeks or over100 years.
How big is a sewer rod?
A sewer "rod" is normally no larger then 3/8 of an inch diameter BUT a SEWER Cable can be as large as 11\4" even the small sewer rods can have large heads to maintain sewers as large as 36"
What is the correct amount of pitch for 6 inch diameter sewer pipe?
.25 per inch per foot
