motor is working but wiper blades do not move.
To fix windshield wipers on a Volvo 940 try using new wiper fluid and cleaning the windshield and wiper blades before you replace the blades. It is also important to replace wiper blades regularly.
Sorry to tell you but the only way to get them moving again is to buy a whole new set.
Replace then with new ones.
at the wiper linkage that is at the base of the wiper arms there is a retainer clip that has broken allowing the linkage from the motor to not move the arms. This happened to me on an 1989 ford pick-up once. It was a pretty easy fix once I figured out the right timing of the linkage.
In general, most electric wiper motors have a "home" position at which the motor is to stop when the switch is turned off. If the home position is not detected there is probably a fault in the motor assembly.
If we are talking about the wiper blade (rubber blade and the frame holding the blade) and NOT the wiper ARM...The 1994 Nissan Quest takes a fairly standard 14" rear wiper blade replacement (also 21" drivers side and 20" passenger side replacement windshield wiper blades).For installation, the replacement wiper blades will come with simple-to-follow, step-by-step, illustrated instructions.
First check if your fuse , have gain bad , \if its alright , then check the wiper motor .
The icon needs reset on the computer. Unplugging the battery and hooking it back up will reset the light if this doesn't fix the problem then remove the fuse and replace it.
1. Clean Glass. 2. Wipe the blade of the wiper with soap and water so it feels relatively smooth. 3. Check that the wiper arm is "springy" and is pushing the blade onto the glass well. If this does not fix the problem, the next most logical and inexpensive thing to do is replace the wiper blades with new ones.
change wiper switch
You have to remove the linkage from the wiper motor.
remove wiper arm from shaft.with ignition on, run wiper then switch wiper to off.this will return wiper shaft to the stop position.reinstall wiper arm to shaft with it sitting so as not to be touching frame. try your wipers again. this should fix problem unless you have replaced wiper arms with new ones that are the incorrect length
You have to diagnose it first. With key on and wiper switch on, listen carefully, if you do not hear an electric motor running check the fuse. If the fuse is good and the wiper motor is receiving power and ground, the wiper motor assembly is probably bad. If you hear a motor running but nothing is moving, the wiper transmission assembly is stripped or the linkage is loose and came apart.
The rear wiper sometimes stop in cycle. Try turning on the switch and then gently move the arm slowing to trigger the motor.
get a wiper
My mechanic replaced a pin in my 2002 Pontiac Montana wiper motor and that solved the problem. It was a very easy fix. The pin is visible if you look at the top of the wiper motor.
how to fix wiper relay Chevy silverado 03
You fix them to the wiper arms usually a snap fit
replace wiper motor or gear box
Fix the drive belt.
first check the wiper fuse to make sure it is good. if it is then you need to replace the motor it should be under the vent panel on the outside of the car under the wiper blades I had this problem on a 1998 Rodeo and the fuse and motor were fine but the bushings in the mechanical arms that move the wiper mechanisms had worn out. Those "arms" are located just below the windshield and under the vent. Take a good look at their orientation before you remove them as there is only one way they go back in correctly.
This might be a very simple fix - check the wiper arm linkage for having come disconnected. See "Related Questions" below for detailed instructions on accessing the linkage.
You should be able to see the wiper motor arms through the grill covering them. If the arms are not moving then they have come loose from the motor. You will have to take the grill off to see exactly what the problem is. The arms to the motor and to the blades are held on with plastic couplings and sometimes they come loose or break. You can get the at almost any parts store and they are fairly simple to replace.