0
What else can I help you with?
How do you change a alpha one prop seal?
To change the prop seal on an Alpha One drive, you will need to first remove the propeller, then remove the drive shaft. Next, you can access the prop seal on the driveshaft housing and replace it with a new one. Make sure to properly align and secure all components when reassembling.
How do you know when you need a new distributor in your car or is it possible thAT it may only need a new cap and rotor?
If the distributor shaft has side to side play it is probably worn out. If the shaft has no play just replace the cap and rotor.
How do you change the propeller shaft on your champ RC aircraft?
Before you change out the shaft of your champ, you are going to want to have a exacto knife, needle nose pliers, a new prop shaft with or without the gear attached, and a new prop. First cut the tap holding the fuselage to the wings, then gently hold the clear end piece with the pliers toward the center of the motor, and turn the shaft clockwise while holding that. The shaft should be disconnected from the motor, but trapped by styrofoam. So, take your exacto knife and make a big enough gap for the shaft and gear to get out. Then take your new prop-shaft and gear, and if the gear came on the shaft just pull it off, and put super glue where the gear was (On the straight threads under a little nub on the propeller) and slide the gear on. Let Dry. Then thread your new propeller, flat part of threads toward the gear. then take your completed shaft and place it back into the motor. Take your new or old end cap and twist it back on the end of the shaft. Re-tap the fuselage and you are ready to go!
How do you adjust drive shaft length Mazda 626?
you dont! if you need that then you are buying a new cv shaft.
Can any lacrosse head fit on a stx scti shaft?
Any head will fit on any shaft. But if you but a head on a shaft that is a different brand than the shaft, you may need to drill a new hole into the shaft. The only exceptions are the STX Crankshaft shafts which need certain heads.
How do you change a clutch on a 2.5 v6?
Remove the drive/prop shaft(s) from the gear box, remove the gearbox. Take the clutch and mechanism out and replace with the new one, you will have to use a clutch alignment tool to make sure that the centre hole on the clutch lines up with the crank shaft. Then put the gearbox back on along with the drives/prop-shafts. To be honest seeing as you had to ask the question, I recommend you don't attempt it yourself.
What is a cvc shaft I'm trying to buy a 91 Accord but it says it need a new cvc shaft. Any ideas on price?
front drive shaft check eBay for an idea of price
How do you fix the front drive shaft on your 1996 Chevrolet Silverado?
Assuming you need new U-joints on the shaft I will try to explain... First remove the bearing retaining u bolts from front differential and the tranny. Be careful while separating the shaft from parts( you may have to use a pry bar) that the bearings do not fall out of the cups. There are snap rings on one side of the U joint, remove those with a pair of needle nose pliers and then prop the shaft on a 2x4 or something and pound out the old ujoint with a ball peen hammer and a socket so you do not bend the shaft where the ujoint is in. Once you have it loose wiggle it out and reinstall the new ujoint but do NOT pound it in with the hammer you'll end up damaging the new bearings, repeat with other side if needed. Hope this makes sense and helps you out.
How do you replace propeller seal on 15 hp mercury?
To replace the propeller seal on a 15 HP Mercury outboard, first ensure the engine is off and securely supported. Remove the propeller by loosening the prop nut and sliding the prop off the shaft. Next, take out the old seal from the propeller shaft housing and clean the area. Install the new seal, making sure it fits snugly, then reassemble the propeller and nut, ensuring everything is tightened properly before testing the motor.
Can you put a new golf head on an existing golf shaft?
If the tip diameters are the same then yes. You will need to take it to your local golf shop and they can tell you. If so they will be able to put the new head on the existing shaft very easily.
How do you remove crank shaft pulley megane?
To remove a crank shaft pulley you need to first jack up the car. Next, remove the bold holding the crack shaft pulley in place and remove the unit. Reverse direction to put the new crank shaft pulley on your car.
Is cargo plane same as prop plane in mafia wars?
No, cargo plane is looted in new york and prop plane in cuba
