0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
A battery has emf of 6 v and an internal resistance of 4 ohm it is connected to a 2.6 ohm resistor a switch when switch is open the potential difference between the terminals of a battery is?
6 volts
When checking the high pressure cutout switch with an ohm meter there should be continuity between?
terminals one and two
What is the difference between switch and limit switch?
rectifier diodes handle larger amounts of power. A switching diode handles much less amperage but at a quicker rate. There are switching diodes that can switch power on and off in several nano-seconds.
What is the Illustration of ohm's law?
Ohm's law states that the current through a conductor between two points is directly proportional to the potential difference across the two points, and inversely proportional to the resistance between them
Who is the author of ohm's law?
OHM, who else?!
How much resistance is required to limit the current to 1.5 mA if the potential drop across the resistor is 6V?
Using ohm's law, V=IR then R=V/I =6/0.0015=4000 ohm = 4k ohm resistor.
A battery has emf of 6 v and an internal resistance of 4 ohm it is connected to a 2.6 ohm resistor a switch when switch is open the potential difference between the terminals of a battery is?
6 volts
Can you make 4 ohm output amp switch to 8 ohm?
There is really no amplifier with an output of 8 ohm or 4 ohm. All loudspeaker amplifiers have an output impedance of 0.5 ohm or less. Scroll down to related links and look at "Voltage Bridging".
Hvac limit switch?
limit switch on hvac used to cut off low voltage on heating when system over heat limit
How do you check a brake switch How do you know if its bad?
Put a test light or a an ohm meter between the two leads. Push in or out depending on what kind of brake switch you have. If the ohm meter shows continuity or the test light lights up the switch is all right.
What tool is used to test the continuity of a switch?
ohm meterbuzz boxlamp & batteryetc.
Can i make 4 ohm output amp switch to 8 ohm..?
There is neither 4 ohm nor a 8 ohm output of an amplifier. Less than 0.5 ohm is the output impedance of a loudspeaker amplifier. Scroll down to related links and look at "Voltage Bridging or impedance bridging - Zout < Zin".
What is an example of Ohms Law?
The simplest example of Ohm's Law is an old fashioned dimmer switch in your house. As you turn the dimmer switch up, the light gradually brightens until it reaches full intensity. Conversely, you can turn the dimmer switch down, and the light gradually darkens.The dimmer switch is a variable resistor. That is, the electrical resistance of the dimmer switch changes as you rotate the knob. Ohm's Law tells us that the flow of current is directly proportional to the voltage, and inversely proportional to the resistance. Since the voltage across the switch doesn't change, the only thing that changes is the resistance when you turn the dimmer switch knob.As you turn the dimmer switch down, you are actually increasing the resistance of the dimmer switch. The current is inversely proportional to the resistance, so as the resistance goes up, the current (flow of electricity) goes down, and the light gets darker. This is an example of Ohm's Law.NOTE: This example applies to rheostat switches, and does not apply to modern current-clipping dimmer switches. Rheostat switches are seldom used now because they can overheat, but the illustration is still a useful example of Ohm's Law.
What is the upper control limit of a 1 ohm resistor with a 20 percent tolerance?
A 1 ohm 20% tolerance resistor should not exceed 1.2 ohms actual resistance.
What is over-hoist limit switch on mobile crane?
it s a limit switch to prevent the wire breakage due to increase the hook
What does a limit switch limit?
A limit switch is used to determine how far a moving part of an appliance will travel during its use. They can be manually operated or may work via a sensor.
What is limit switch?
A switch designed to cut off power automatically at or near the limit of travel of a moving object controlled by electrical means
