0
Depends on how much liquid you have. Doesn't really matter if it's colourless or not, either. Colourless doesn't mean invisible. I don't think volume would be your primary concern if your liquid was literally invisible.
If you have a small amount (between 10 and 0.1 ml) I would probably use a graduated pipette to suck the liquid up and then look at how much it comes to (try and evacuate or account for any gas pockets).
If you know exactly what your liquid is (say, water) a better way would be to weigh something before you put the liquid into it, then weigh it again afterwards. The difference in weight can be used to get a volume of the liquid if you know its density. This will not work well at all for mysteries or mixed solutions.
BUT what you can do is use a micropipette to take an EXACT amount of your mystery liquid or solution then weigh this exact amount. Do this for 1ml (or scale the weight afterwards to 1 ml's worth) and you just got the density. Now weigh your solution and work out the volume using V = Mass/Density.
(Don't forget the add back in the 1ml or so you took out to find the density in the first place!)
A more common solution to the problem would be to just use a measuring cylinder. This is less accurate but actually it's usually good to 0.1 of a cm accuracy, which isn't bad at all. Remember that surface tension can cause a bulge at the top of your liquid and you should measure from the bottom of the bulge (where the liquid meets the glass) not the top.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Is a meniscus the scale on a Triple beam balance?
If it is, I'll be damned.a meniscus, as far as I know, is the maximum curve of a liquid in a measuring cylinder. you read the volume from there.
What should you look at to measure a volume of water in a graduated cylinder?
Place the cylinder on a flat surface. Read the volume contained in a graduated cylinder or volumetric flask, by comparing the bottom of the meniscus (the curved surface of the liquid),at eye level, to the nearest graduation or ring.
How is the meniscus used in measuring the volume of liquids?
AnswerA meniscus is when the attractive force between the liquid and the container is greater than the attraction between the individual liquid molecules. This causes the liquid to "stick" to the side of the container, creating a curve. The volume must be read at the bottom of the meniscus.
What is a graduated cylinder used for in science?
A graduated cylinder is a piece of laboratory glassware used to accurately measure out volumes of chemicals for use in reactions. They are generally more accurate and precise for this purpose than beakers or erlenmeyer flasks, although not as precise as a volumetric flask or volumetric pipet. They come in a variety of sizes for different volumes, typically 10 mL, 25 mL, 50 mL, or 100 mL and up to as large as 1 or 2 liters.Determine the volume contained in a graduated cylinder by reading the bottom of the meniscus at eye level.In other words, holding the graduated cylinder at eye level, the bottom of the curved surface of the liquid (called the meniscus) is where you read off the mark on the graduated cylinder to determine the volume properly.
How could the volume of a gold nugget be found using water and a graduated cylinder?
Fill the graduated cylinder half full (may be more or less depending on the actual situation) and drop in the gold nugget. Read the final volume mark and subtract the initial volume from the final volume. This difference in volume is the volume of the nugget. This is related to the principle of buoyancy and it is said to have had a colourful story behind its discovery. Read the Wikipedia article on 'Eureka (word)' to learn more.
What meniscus is being read if you measuring the volume of dark colored liquids?
1.read the bottom of the curve 2. you must read the meniscus at eye level
How can you find the volume of a liquid?
First you put the liquid in the graduated cylinder.Then you read the volume at the bottom of the meniscus.The meniscus is the slight curve at the edges of the surface where the liquid touches the container.
Law of lower and upper meniscus levels in determining liquid solution?
In measuring liquids using graduated cylinder, there are two things to consider. 1.) CLEAR LIQUID and 2.) COLORED LIQUID (as we may say) In identifying the volume of CLEAR LIQUID (e.g. plain water, oil, alcohol, etc.), THE LOWER MENISCUS is read. For the COLORED LIQUID (e.g. soy sauce, ketchup, etc. ) the upper meniscus is get, since there is only one meniscus there.. (meaning there is no upper & lower meniscus.)
Reading the volume of liquid inside the graduated cylinder?
Always read from the bottom of the meniscus (where the liquid reaches up the side of the container).
How do you read CC14?
CC14 is typically read as "carbon tetrachloride." It is a compound made up of one carbon atom and four chlorine atoms. It is a colorless liquid with a sweet odor, commonly used as a solvent and in fire extinguishers.
Does a flask have a meniscus?
Yes. A meniscus is a visible curve in a liquid caused by the attraction of the liquid for the sides of the flask. Read the volume of your flask from the bottom of the meniscus.
How do you read the volume of dark colored liquids and clear liquids?
tangina gago kaya nga ako nag tanong tanga lang
Why is it important to clamp the burette vertically?
To ensure that the actual volume of liquid delivered into the conical flask is read accurately
What is a meniscus why it necessary to know about it when measuring liquids?
The meniscus is the concave line of liquid that forms in a graduated cylinder (measuring volume) due to that liquid's adhesion (the tendency to want to stick to other things). When measuring a liquid's volume in a graduated cylinder, you read the volume from the bottom of the meniscus. Therefore, the meniscus does not measure anything, it is where you measure a liquid's volume from.
How do you find volume of a liquid and gas?
This depends to some extent on the quantity of liquid or gas that you are trying to measure, but for normal amounts, you would pour the liquid into a graduated cylinder and then read the volume off of the markings on cylinder, and for a gas, the volume is always going to be the same as whatever container it is in, since gas expands or compresses, according to the size of its container.
What is volume by displacement?
Volume displacement is the method used to find the volume of small or irregularly shaped objects by noting the difference in the level of liquid before and after after immersing an object into a graduated cylinder or beaker of liquid. For a small object immersed in a graduated cylinder or beaker, the volume displaced by the object can be read directly from the scale on the container.
Is a graduated cylinder used for?
A graduated cylinder is a usually glass (but some are plastic) quantitative piece of laboratory equipment. Graduated cylinders are used for accurate liquid measurement. To read a graduated cylinder correctly, the volume of liquid contained is measured at the bottom of the meniscus, which is at the top of the liquid, in the exact center of the cylinder, and not at the side where the liquid touches the glass (or plastic).A graduated cylinder, measuring cylinder or mixing cylinder is a piece of laboratory equipment used to measure the volume of a liquidit is used for the precise measurements of liquids.To measure volume of liquids.Pour liquid in the graduated cylinder then find the lower meniscus (lower meniscus's lower curve of liquid's surface) read the volume off the graduations.Measurement of liquids OR a container used to find the volume of an object in Liters.
