You will need to remove the headliner. With the headliner removed you will be able to see the overhead console retaining screws. Remove the retaining screws.
how to I remove the overhead console on the S 10 Blazer?
To remove the overhead console you will first need to disconnect and isolate the negative battery cable. Remove the overhead screws and pull straight down on the console.
Remove the Toyota Camry headliner. The overhead console retaining screws will be visible. Remove the retaining screws and the console will come off.
The 1999 Dodge Durango overhead console wiring connections are beneath the overhead console. You will need to remove the overhead console?æin order to access the wiring connections.
Remove the screws that hold the headliner in place. With the headliner removed the overhead console retaining bolts will be visible. Remove the retaining bolts. Remove the wiring harness from the console.
In ebay.com, search by overhead console.
remove the screw near the front of the overhead console. Using a trim removel tool, gently pry the unit away from the headliner on the left and right side of the overhead console.
Open the cover and locate the screws on each side of the console. Remove them with a Phillips screwdriver. The console will get a little loose. Do not pry it now or intend to remove it by pulling the loose end. Get the part of the console that is close to the windshield and try to get your fingers in between the ceiling and the base of the console. Pull the console down once you are able to grab the cover. Remove the connector. Installation is the opposite.
# Disconnect and isolate the remote negative battery cable. # Remove the overhead console retaining screw, located in the front of console near the windshield. # Using your fingertips, grasp the sides of the overhead console and pull straight down evenly to disengage the two snap clips at the rear of the unit. # Lower the overhead console far enough to access the wire harness connectors. # Disconnect the control module, courtesy lamps and if equipped, the power sunroof switch electrical connectors. # Remove the overhead console assembly from the vehicle.
I googled "04 Dodge Ram Manual" and downloaded the service manual from one of the links, which is different than the owners manual. The service manual is 2000+ pages long....here's what is says about the overhead console removal procedure....REMOVAL OVERHEAD CONSOLE REMOVAL (1) Disconnect and isolate the negative battery cable. (2) Remove the overhead console retaining screws, located in the sunglass storage bin. (3) Using your fingertips, grasp the sides of the overhead console and pull straight down evenly to disengage the two snap clips at the front of the unit. (4) Lower the overhead console far enough to access the wire harness connectors. (5) Disconnect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (6) Remove the overhead console from the vehicle. INSTALLATION (1) Position the overhead console in the vehicle. (2) Connect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (3) Grasp the sides of the overhead console and push straight up evenly to engage the two snap clips at the rear of the unit. (4) Install the overhead console retaining screw, located in the front of console. Torque the screw to 1.2 N·m (10 in. lbs.). (5) Connect the negative battery cable. I googled "04 Dodge Ram Manual" and downloaded the service manual from one of the links, which is different than the owners manual. The service manual is 2000+ pages long....here's what is says about the overhead console removal procedure....REMOVAL OVERHEAD CONSOLE REMOVAL (1) Disconnect and isolate the negative battery cable. (2) Remove the overhead console retaining screws, located in the sunglass storage bin. (3) Using your fingertips, grasp the sides of the overhead console and pull straight down evenly to disengage the two snap clips at the front of the unit. (4) Lower the overhead console far enough to access the wire harness connectors. (5) Disconnect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (6) Remove the overhead console from the vehicle. INSTALLATION (1) Position the overhead console in the vehicle. (2) Connect the EVIC, CMTC electronic module and the reading/courtesy lamps electrical connectors. (3) Grasp the sides of the overhead console and push straight up evenly to engage the two snap clips at the rear of the unit. (4) Install the overhead console retaining screw, located in the front of console. Torque the screw to 1.2 N·m (10 in. lbs.). (5) Connect the negative battery cable.
remove the two light lens be careful not to break them. then remove the two torx screws behind the lens. give a slight pull down on the front of the console to remove the two clips and you are done.
Best information link regarding center console removal for Yukon/Tahoe below. http://www.salient-designs.com/images/Paper%20Works/SD253B%20Instructions.pdf