Top Answer
User Avatar
Wiki User
Answered 2010-02-14 08:01:20

to unbolt the bell housing you un bolt the six bolts that screws through the trans bell housing into the engine. they go from the back towards the front of engine. be sure to unbolt torque converter bolts too.they go through the flywheel

User Avatar

Your Answer


Still have questions?

Related Questions

Is a Chevy 350 th transmission bellhousing?

No, the engine is not the transmission bellhousing. The bellhousing is a separate piece all together.

Will the bellhousing from a 350 fit a 496 stroker engine?

If it's a 496 Chevy, yes.

Does a Chevy inline 6 have same bolt pattern as Chevy 350?

Same bolt pattern for what? For the bellhousing and starter, yes. For just about everything else, no.

Will a 700 r4 bolt on to a 350 small block?

Absolutely. Chevy bolted them to the 350 straight from the factory. The 700 R4 has the exact same bellhousing bolt pattern as the 350 and 400 turbo does.

How do you remove bellhousing from citroen xsara Picasso?

Remove bellhousing from citroen xsara picasso

Can you put a 350 Chevy engine in a 1985 s10 blazer without changing transmissions?

No, you can't. transmissions bellhousing is different in 60° V6 and L4

How do you get the top 4 bellhousing bolt out of a 1996 Chevy blazer s10?

It is a tight fit, but you can get to them from the top if you remove the distributor first.

Were do you get a bellhousing for a 350 to fit 1993 Toyota tranny?

You can't, They don't make a after market bellhousing to do that. You will have to change the transmission to.

How do you remove the valve cover on a 96 Chevy 34 silverado?

if its a 350 remove alt. first

How do you remove the heads on a Chevy 350?

take out the cylinder head bolts

How do you change a Chevy 350 flywheel?

remove the enigine and then take out flywheel bolts

Will a Chevy 350 bolt up to a ford 4 speed transmission that fits a 300 in line 6?

You would need to purchase the correct bellhousing, then it should work out fine.

How to change a head gaskets 1992 Chevy 350?

Remove the cylinder head from your 1992 Chevy 350 cubic inch engine. Remove the head gasket and clean the surface. Put the new head gasket on and reverse the process.

How much horse power does a small block Chevy 350 in 1979 have?

look on the bellhousing on the driver's side and write the numbers down and look the numbers up. Google 350 Chevy casting numbers online or go to your local library. the year and the casting number will give you all the specs on that engine.

How do you remove the water sening unit on a 350 Chevy?

It's threaded. Twist it counterclockwise.

Will a Chevy 4-speed manual 4x4 transmission from a 350 bolt onto a Chevy 454 motor for my 85' Chevy?

bell housing are the same for bbc and sbc. clutch will need to be correct and check the mounting location lengths compared to the bellhousing for fitment.

How to remove cylinder heads on a 1995 Chevy 350?

need year of vehicle first.1995

How long does it take to remove a Chevy 350 motor from a 1999 suburban?

About 3 hrs. To take it out.

Will a 1993 454 motor fit a bellhousing off a 1991 350 motor?


Is the starter on a 1970 Chevy 350 different from a 1978 Chevy 350?


Is a 99 GM 1500 4L60E transmission compatible with a 96 Chevy tahoe 4L60E?

no the bellhousing on 99 is made like a ford starter mounts to bellhousing and not to motor and it has a full bellhousing instead of open on bottom

How do you replace the valves in a Chevy 350 engine?

this is a mechanics job you have to remove inlet manifold,exhaust manifolds,and then remove heads to replace the valves

Does a 1995 Chevy 4.3L have a integral bellhousing?

No. The bell housing is actually on the transmission.

How can you fix th reverse in a Chevy 350 transmission?

Remove the trans and take it to a transmission repair shop.

Will a distributor from a 90 Chevy 350 work in a 99 Chevy 350 vortec?