0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you change out an EGR valve on a 1997 Nissan pickup 2wd?
You need to take the air cleaner off. Then disconnect the vacuum hose going to your brake booster at the check valve point. There is a valve (EGRC-BRT) next to the EGR remome the the clamp on the braket that is holding the brake booster hose and swing it out of your way. Next you need to remove the vacuum hose from the EGRC-BRT valve and remove the valve nad the bracket that hold the vave. Now you can get to the EGR pipe which attaches to the EGR. Remove the pipe then remove the the bolts that hold the EGR valve.
How do you change brake booster on 1995 Chevy lumina?
unhook the 4 brake lines and the wires from the master cylinder/ABS, take off the 2 15MM nuts holding the unit to the booster, remove the unit, take off the exhaust shield for the crossover pipe, move the cruise control unit out of the way, remove the pin and take the rod off of the brake pedal, twist the booster counter clockwise until it pops loose from the firewall. you may have to remove a few things to get the exhaust shield off easier.
What will cause a opel ts not to idle?
As you said when you tramp brake engine idles ruf and then cuts out 2 things 1 return valve in brake vacuem pipe from intake to booster 2 Brake booster sucking air
What is the pipe that comes out of the 350 engine intake behind carburetor that has three holes for connections?
That is what is called a vacuum tree. The large connection is for the power brake booster. One smaller one is for the transmission modulator and the third one is for the air conditioner.
What are the disadvantages of vacuum braking system over the other?
· A very large brake piston and cylinder are required to generate the force necessary on the brake blocks. · The existence of vacuum in the train pipe can cause debris to be sucked in · A considerable volume of air has to be admitted to the train pipe to make a full brake application
You own a 92 Lincoln Continental. When you press the gas pedal something makes a hissing noise kind of like air through a hose. Your car will also not go over 30-35 mph.?
Two things come to mind. Blocked exhaust system or large vacuum leak. Check the entire exhaust for a bent pipe. If this checks OK, then check the large vacuum hose going to the brake booster. If your brake pedal is hard to push, suspect the booster is defective. A blocked or plugged exhaust would be what I would suspect as the culprit. The catalytic converter may be stopped up and need replacing or the tail pipe can be bent closed.
What is the purpose of a brake pipe?
A brake pipe is an important part of a car. It is available in rolls of 25 foot long. Cars where the brake pipe is damaged are a danger in traffic. A good working brake pipe is important for the brakes.
Why do the car feels like it want to cut off when pressing on the brakes?
hi u could hav a leak on u vacuum pipe from u engine to the brake servo or u brake servo is faulty
What factors can cause brakes to fade or fall?
Worn brake shoes or pads. A leaking brake pipe. Low brake fluid. Air in the brake fluid pipe.
How do you remove water pump on 2000 Pontiac sunfire 2.2 liter?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
How do you remove the water pump on a 1998 Chevy cavalier Z24?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
How do you remove water pump on 2000 Pontiac sunfire?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
