0
I just removed one on a 94 Olds Regency which I assume would be very much the same. You have to pry any panels with switches/knobs out of their place first. The panels have plastic tabs along the top edges and plastic hooks along the bottom edges, so be sure to pry from the top. Once the top is away from the door, lift up on the assembly to lift the hooks up and away from the door. Everything is plastic so go slowly and in small amounts. Any panel will slip over the door handle with a little twisting.
Next, look carefully at the back side of those panels for ways to remove the connectors from the switches. They have tabs that need to be pried out just enough to slide the connectors off. Once that is done you can take a flat screw driver and begin prying the door panel away from the door. It is held on by serrated nylon "studs". They all will pry out of their sockets. Once all those are out you will have to lift the door panel up to get it loose from the top. There is an edge on the door frame that tilts outward in order to allow the top edge of the door to hang on it. This may take some wiggling and some effort to get it up off the hanger edge, but it will come off. Feed the wiring back through the door and remove the door panel.
When you get ready to replace the door panel, just reverse the procedure, confirming that any electrical connectors are replaced and secure. Make sure that all of the nylon "studs" are in place in the door panel. Also make sure that as you are lining up the door panel to replace it, to look behind the panel to assure that all the nylon "studs" are lined up to pop back into their original holes. Once you do this you can begin pounding the front side of the panel with the heel of your hand to press the nylon studs back into place. That should do it.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Builder of America's first exported car?
Oldsmobile (0lds)
Where do you plug in the new coolant on a 96 0lds sierra?
If you are talking about the a/c it is on the low side.
How do you remove air conditioner compressor on 92 0lds delta 88?
Disconnect the power. Unbolt the compressor, loosen the belt. Remove belt. Remove bolts that hold pipe or hose assemblies on. Replace in reverse, Use new seals vacuum check to -30 bars for 30 minutes then recharge,. Also change accumulator and ALL o-rings and seals.
Location of flasher relay on 1993 0lds 88?
The flasher relay on most vehicles is located at the fuse box or brain. It is either round or square and is attached to the fuse box at one of the corners or sometimes at two corners.
Driver side blowing hot air and passanger side blowing cold air on a 95 0lds nine eight?
its your blend door actuator behind the glove box most likely Mine did the same until i replaced it
Can a Chevy 350 fit in a 1986 cutlass supreme that has a 350 0lds if so what will need to be replaced motor mount?
1984 Cutlass Supreme in 1984 was a G-body RWD car right?The Gen1 to Gen3 Chevy small block including 350 will fit in any of these cars.Transmission mating:If original engine is Chevy V8 (usually 305 or 350) or Chevy V6 (229) no changes needed. Otherwise, a different bell housing or flywheel or torque converter may be required.Mounting:Go to an auto parts store and ask for motor mounts for your car, specify year make and model. Lie about the engine. Say it's a 305. 350 may not have been available for your car as OE, but 305 is a small block with the same mountings.Carburetor:Use an appropriate Quadrajet for your 350 and ECM to match the carb. Otherwise, a different carb can be used, but most won't provide the same combination of driveability/performance for street/strip applications.Note that a 307 is an Oldslomobile engine and a 231 is a Buick engine both of which may require some minor changes to mountings and transmission mating.An 86 olsmobile only came as a 307 or the smaller v6. If the car already has a bigger olsmobile engine in it then it should already be the same as a Chevy 350 although the numbers may not match (305 is the same as 307.)You should have no problem putting in a 350.
What is the standard size tire for a 1989 Oldsmobile 98?
Hi There are 5 different models of 89 0lds 98's they take sizes from a 205-75 x14 to a 215- 65 x15 any tire shop can look at the car and get the information for you. also check the drivers door sticker it should be listed there. Pat
What would the cause be for a 1994 0lds delta 88 3.8 liter to die out then you can restart it and go again?
Have you checked the fuel pump and gas tank? Also fuel lines and fuel filter. Low flow will cause one to die because of fuel starvation, but then start again because it takes little to start.
My service engine soon light just came on in my 1999 0lds alero does this mean my car will soon break down?
no, most likely you just need a basic tune up or you need to check fluids. I've drove cars for months with those stupid lights on and never did my car just break down bt you should for sure take it in and have it serviced.
