0
I downloaded the manual for the Discovery II. I have done the brakes on mine and here is wht the manual said:
Brake discs must be renewed in pairs, unless
one disc requires changing before 1000 miles
(1500 km) from new.
Remove
1. Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2. Remove road wheel(s).
3. Remove 2 bolts securing brake caliper to rear
hub.
4. Release caliper and tie aside clear of brake
disc.
CAUTION: Do not allow caliper to hang on
brake hose.
5. Remove screw securing disc to drive flange.
6. Remove brake disc from drive flange.
Refit
1. Clean mating faces of drive flange and new
disc.
2. Fit brake disc to drive flange, fit screw and
tighten to 13 Nm (10 lbf.ft).
3. Clean mating faces of caliper and hub.
4. Fit caliper and tighten bolts to 95 Nm (70 lbf.ft).
5. Fit road wheel(s) and tighten nuts to 140 Nm
(103 lbf.ft).
6. Remove stand(s) and lower vehicle
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Where is the fuel filter located on a 2000 Landrover Discovery 2?
Behind the right side rear wheel.
How do you get door locks to work on landrover discovery 3?
my discovery 3 rear door lock will not lock with remote
How do you replace a crankshaft sensor on a 1997 Landrover Discovery?
Begin by removing the rear engine cover from your 1997 Land Rover Discovery. Remove the crankshaft sensor wiring harness. Remove the crankshaft sensor retaining bolts. Reverse the process to install your new crankshaft sensor.
Replace rear wheel bearing on 2002 Mercury Mountaineer?
Remove the rear tire and wheel. Remove the axle end cap. Remove the rear wheel seal. Remove the rear wheel bearing. Reverse the process to install the new wheel bearing.
How do I remove a rear wheel bearing on a VQ Statesman?
Begin by removing the rear tire and wheel. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing.
How do you replace rear wheel bearing on a Ford Fiesta 2003?
Remove the rear tire and wheel. Remove the axle end cap. Remove the wheel bearing seal. Remove the wheel bearing. Reverse the process to install the new wheel bearing.
How do you replace a rear wheel bearing on a 1997 Mercury Cougar?
You will need to remove the rear tire and wheel. Remove the axle end cap. Remove the wheel bearing nut. Remove the wheel bearing and the wheel seal. Reverse the process to install the new wheel bearing.
How do you remove a tire from a 2000 Harley Davidson?
loosen up the rear axle nut and loosen up the axle adjusters so the rear wheel moves forward, Now remove rear brake caliper from rear brake caliper mount and the remove rear axle and lower rear wheel and slide belt off rear pully. and remove the rear wheel. http://www.ronincycleparts.com
How do you remove rear wheel bearings?
To remove rear wheel bearings, first jack the car up so that the rear wheels are off the ground. Then grip the rear tires at 6 and 12 o'clock, and push them in. Finally, remove the transmission tray, engine tray and the plastic cover from the suspension wishbone.
How do you remove rear wheel bearings on a Chevy Cavalier?
Remove the tire and wheel from your Chevy Cavalier. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing.
How remove rear wheel from Husqvarna riding mower?
You can remove a rear wheel from your Husqvarna riding lawnmower by loosening and removing the lug nuts. The wheel should come off.
How do you change rear wheel bearings on 1978 Corvette?
How to remove rear wheel bearings on a 1978 corvette..?
