0
OK, most cars its really easy, just a few steps you have to go through. FIRST, if you are replacing a window odds are the old one is broken, so take off your door panel (usually a screw on the door handle surround, its kinda hard to see sometimes), and the if you have roll up windows take a rag and point the window handle down, and stick the rag under the handle base and wiggle it in a U pattern and it will snag the little clip holding the hanlde. SECOND, Once you have you the door panel off peel back the plastic(its a plastic sheet, keeps the water out) once you get it out take a vacuum and get out all the broken glass out of it, and take a flathead screw driver and get the glass chunks out of the window channels. THIRD, once you have all the old glass out, roll down the window and look for a bar that goes horizontal(it typically has 2 bolts on it and will have the rest of the glass attached to it) and take that off and trash it(keep the bolts). FOURTH, grab the new window and put it into the channel with the smaller end down(front) and kinda work it into place. once into place guide it down and line up that horizontal bar, and bolt it in place. FIFTH, test it out and if all is good put it all back together. DONE!!!!
What else can I help you with?
How do you replace speakers on a 2007 Chevy pickup?
take door panel off
How do you adjust a door on a 2000 Chevy Silverado pickup to eliminate wind noise at the top of the door?
Replace door moulding
How do you replace Chevy Venture back window?
By relpaceing the hole door
How do you replace the rear vent window on a 2001 Chevy Blazer LS 4x4 2 door?
You can replace the rear vent window on a 2001 Chevy Blazer LS 4x4, 2 door with Direct Fit Power Window Regulators.
Can you change the power window switch in a 1986 Chevy silverado pickup without removing the door panel?
No you can't.
How do you replace a window regulator for a 2005 dodge ram pickup?
First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.
How do you replace a passenger window on a '75 Chevy pickup?
1st poll off the door panil. 2nd ajust the window so the cradall scrooes can be gotten to throgh the holse in the door. 3rd w/ a phillups scrooedriver, take out the two scroos holding the window. pull up and out window. The prosess of putting one in is doing evrey thing inrevers.
How do you replace driver's door mirror on 1989 Chevy pickup truck?
All you have to do is if its a power window truck is take the screws out of the door panel and pop all the clips loose. Then unplug the window and lock switches. There are 3 bolts that hold the mirror on behind door panel. If manual locks and windows, mainly the same but dont have to unplug wires but have to pop clip off handle for window and lock.
How do you put spring back on interior door handle of 98 Chevy pickup?
how do you install spring on interior door handle of a 98 chevy pickup
How do you replace the door window on a 1990 Chevy S-10 pickup truck?
We could write a book on the correct procedure to replace a door window in a Chevy S-10 pickup. There are far too many things to do, and not do when doing it. Also, "words" are useless, in some areas, and pictures are needed to illustrate the words. Go to your local auto parts store and pick up a Haynes manual or Chilton manual. These are filled with "how to" with pictures and illustrations to guide you on how to perform these tasks. Short on cash? Most libraries have a plethora of books and the manuals I indicated in their "resource" section.
How do you replace the passenger side rear door window on an '85 Chevy Chevelle?
To replace the passenger side rear door window on an '85 Chevy Chevelle, first, remove the door panel by unscrewing any fasteners and gently prying it off. Next, disconnect the window regulator and any associated electrical connectors, then carefully slide the old window out of the channel. Install the new window by sliding it into place, reattach the window regulator, and finally, reassemble the door panel by securing it back in place. Ensure everything is functioning properly before closing the door.
How do you replace the window crank on a Chevy lumina 1997?
Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
