0
LIFT CYLINDER REMOVAL AND INSTALLATION 1. Operate the top to the fully raised position. 2. Remove the rear seat cushion and the quarter trim panels. 3. Remove the cylinder assembly support pivot bracket retaining bolts and bracket. 4. Remove the hair pin clip and clevis pin at the top end of the cylinder and remove the cylinder. 5.Disconnect the plug the hydraulic lines at the upper and lower ends of the cylinder. Use absorbent cloths to catch any fluid that leaks out. 6. Position the cylinder in the floor bracket with the hose connection facing down. 7. Connect the hydraulic lines to the cylinder. 8. Install the clevis pin and hair pin clip at the top end of the cylinder. 9. Position the cylinder assembly to the support pivot bracket and install retaining bolts. 10. Loosen the reservoir filler plug and operate the top assembly two or three times to bleed any air from the system. 11. With the top in the raised position, check the reservoir fluid level. 12. Install the quarter trim panels and the rear seat back and cushion. LIFT CYLINDER REMOVAL AND INSTALLATION 1. Operate the top to the fully raised position. 2. Remove the rear seat cushion and the quarter trim panels. 3. Remove the cylinder assembly support pivot bracket retaining bolts and bracket. 4. Remove the hair pin clip and clevis pin at the top end of the cylinder and remove the cylinder. 5. Disconnect the plug the hydraulic lines at the upper and lower ends of the cylinder. Use absorbent cloths to catch any fluid that leaks out. 6. Position the cylinder in the floor bracket with the hose connection facing down. 7.Connect the hydraulic lines to the cylinder. 8. Install the clevis pin and hair pin clip at the top end of the cylinder. 9. Position the cylinder assembly to the support pivot bracket and install retaining bolts. 10. Loosen the reservoir filler plug and operate the top assembly two or three times to bleed any air from the system. 11. With the top in the raised position, check the reservoir fluid level. 12.Install the quarter trim panels and the rear seat back and cushion.
What else can I help you with?
Does a 2001 mustang convertible 3.8 have a coil?
yes.
Where is the convertible top motor in a 2001 Mustang?
Behind the back seat
How do you replace the thermostat in a 2001 Ford Mustang 6 cylinder?
The thermostat is in a housing at the engine end of the upper rad hose. When you replace it make sure the spring goes toward theengine.
2001 Mustang GT Convertible 5.0 liter v8 is how much HP?
a 2001 has a 4.6 engine. i think it has 265 hp
What fuse controls the courtesy and interior lights in a 2001 mustang convertible?
This information can be found in your owner's manual. Don't have one, get one. Dealer or salvage yard is a source. Hi I own a 2001 Mustang convertible. The fuse for the interior light who are on the inside mirror is fuse number 7 an it is a 15A
Where is cylinder 4 on a 2001 Ford Mustang?
On a 2001 Ford Mustang , 3.8 liter V6 engine : firewall 3 - 6 2 - 5 1 - 4 front of vehicle
Does a 2001 Ford Mustang have timing belt?
No , the 3.8 liter V6 engine in a 2001 Ford Mustang has a timing CHAIN and the 4.6 liter V8 in the 2001 Ford Mustang GT has one timing chain to each cylinder head ( total of 2 timing chains )
Number one cylinder on a 2001 mustang gt?
Passenger side front of engine is the #1 plug.
Where is the brake fluid cap on a 2001 Ford Mustang?
On top of the Master Cylinder, driver's side, near the firewall.
Which cylinder is 3 on 2001 mustang v6?
FIREWALL 3 - 6 2 - 5 1 - 4 FRONT
Replace timing belt on 2001 Ford Escape 4 cylinder?
how do I set the timing on 2001 ford escape xlt 4 cylinder
How do i replace the slave cylinder in a ford focus 2001?
By going to a garage
