answersLogoWhite

0

I've never had to change mine, but it's an in-line filter located near the gas tank.

User Avatar

Wiki User

19y ago

What else can I help you with?

Related Questions

Where is the Canister purge valve on a 2001 sunfire?

Cannot locate canister purge valve on a 2001 pontiac sunfire 2.2


Change reverse lights on Pontiac Sunfire?

To change the reverse lights on a Pontiac Sunfire you need to locate it on the left side of the transaxle. Then, unplug the electric connector and remove the switch along with the socket.


Where are the sparkplugs on a 1999 Pontiac sunfire?

on the engine. Your best bet is to take it to the shop if you cannot locate them. Sorry


How do you replace dash board lights in a 2005 pontiac sunfire?

To replace the dashboard lights in a 2005 Pontiac Sunfire, first, disconnect the negative battery cable for safety. Remove the dashboard trim panel by unscrewing any screws and gently prying it off. Then, locate the bulb sockets on the back of the gauge cluster, twist them counterclockwise to remove, and replace the burned-out bulbs with new ones. Finally, reassemble the dashboard and reconnect the battery.


How do you replace the turning signal flasher on a 2004 Pontiac sunfire?

To replace the turning signal flasher on a 2004 Pontiac Sunfire, first, locate the flasher unit, which is typically found under the dashboard near the steering column. Remove the old flasher by pulling it straight out of the socket. Insert the new flasher into the socket, ensuring it is securely in place. Finally, test the turn signals to confirm they are functioning properly.


How do I repair a blower motor on a 1996 Pontiac Sunfire that only works on 'high'?

Your wiring is probably messed up, happened to me. Locate the wires from the blower to the controls check them and replace as needed. Assuming no wiring problem check and replace the blower motor resistor.


How do you replace the cabin air filter on a 2004 Pontiac vibe?

To replace the cabin air filter on a 2004 Pontiac Vibe, first, locate the filter access panel, which is usually found behind the glove compartment. Open the glove compartment and remove any contents, then gently squeeze the sides to detach it and lower it. Remove the old filter by sliding it out, and install the new filter in the same orientation. Finally, reassemble the glove compartment and ensure everything is securely in place.


How do you replace blend door actuator on 1997 Pontiac Bonneville?

locate blend door actuator for 1997 pontiac bonneville se


Air filter on rx330 Lexus?

cant locate where sir filter is on lexus2005rx330 and how to replace it also have no idea how to replace rear wiper blade


How do you install license plate light 1995 pontiac sunfire?

To install a license plate light on a 1995 Pontiac Sunfire, first, locate the light assembly at the rear of the vehicle. Remove the screws or clips securing the light housing, then carefully pull it out. Replace the old bulb with a new one, ensuring it fits snugly, and reassemble the light housing by securing it back with screws or clips. Finally, test the light to ensure it functions properly.


How do you replace a crankshaft sensor on a 1997 2.2 Pontiac sunfire?

To replace the crankshaft sensor on a 1997 Pontiac Sunfire with a 2.2L engine, first disconnect the negative battery cable to ensure safety. Locate the crankshaft position sensor, which is typically found near the bottom of the engine, near the flywheel. Remove any necessary components for better access, then disconnect the wiring harness and unbolt the sensor using the appropriate socket. Install the new sensor by reversing the steps, ensuring a secure connection and proper alignment.


How do you replace fuel filter on 2003 pontiac aztek?

To replace the fuel filter on a 2003 Pontiac Aztek, first, relieve the fuel system pressure by removing the fuel pump relay and starting the engine until it stalls. Next, locate the fuel filter, which is typically found along the fuel line under the vehicle. Disconnect the fuel lines from the filter using appropriate tools, then remove the old filter and install the new one, ensuring the flow direction is correct. Finally, reconnect the fuel lines, replace the fuel pump relay, and check for leaks before starting the engine.