0
How do you replace tensioner pulley on a 1999 2.2 liter cavalier?
Wiki User
∙ 11y ago
Remove bolt from coolant bottle and set to side to have room to work. bungee cord belt from alternator to ac line, so belt doesn't come off other pulleys. put 3/8 inch ratchet or breaker bar on tensioner & release tension while you slip belt off. Take tire off passenger front side. Remove splash sheld. you will see tensioner. remove it with a 15mm wrench (ratchet 7 socket won't fit, limited clearance. reverse everything to put back together.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Replace Serpentine belt on Monte Carlo 3.1?
Loosen the tensioner pulley on your Monte Carlo 3.1 liter engine. Slide the tensioner pulley to the right. The serpentine belt can be removed. Put the new serpentine belt on and slide the tensioner pulley to the left.
How do you replace serpentine belt on a 2000 Chevy cavalier 2.2 liter?
Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner
How do you remove the power steering pump on a 1993 Cavalier 2.2 Liter?
There are access holes in the power steering pump pulley which allow the 13mm bolts that fasten the pump to the tensioner plate to be removed. Once these bolts are out the pump can be swung out. This also unblocks one of the tensioner plate bolts-- if replacement of the tensioner plate is necessary.
Where are the timing marks on a 2.2 Chevy Cavalier?
The Chevy Cavalier 2.2 liter engine timing marks can be found on the main pulley. The timing marks will be scattered around the outside of the pulley.
Can you replace your 2.2 liter with a 2.4 liter echotech engine on a 99 Chevy cavalier?
No
What size is the idler pulley bolt on a 2001 Pontiac sun fire 2.2 liter?
Or tensioner bolt if different
How do you tighten serpentine belt on 2005 Chrysler 300 2.7 liter v6?
You can tighten the serpentine belt on your 2005 Chrysler 300 by tightening the tensioner pulley. Push the tensioner pulley to the right until the serpentine belt is tight.
Is the tensioner pulley on a 1999 jeep Cherokee standard or reverse thread?
standard thread on the 99 model with 4.0 liter.
How do you replace the belt on a 1992 Chevy Cavalier?
on a 2.2 you just need a 3/8 drive rachet or 15mm wrench to release tension from tensioner.2.4 liter is about the same but you must remove the motor mount.gm Jim
How do you tighten the serpentine belt on a 93 Saturn SC2 1.9 liter dohc?
You don't, they have a tension pulley that does that automatically. If the belt is too loose, the pulley most likely has to be replaced. Thecommi ::: The serpentine belt is held by tention with a automatic belt tensioner. If the serpentine belt is loose, you will most likely have to replace the entire belt tensioner assembly. the assembly comes with a new pully.
How do you remove replace the tensioner on a 96 3.3 liter Caravan?
You have to remove the belt first, this is easiest with a tensioner tool. Then the nut that holds it to the bracket is on the backside of the tensioner and needs to be done from the bottom.
Can you adjust the tension on the belt on a 1994 ford thunderbird 3.8 liter v6?
No you can not. You need to replace the tensioner.
