answersLogoWhite

0


Best Answer
StarterRemove starter on a 1999 rodeo 3.2 v6 first this is no easy task you will need torches and air tools unless you really have ALOT OF PATIENCE ! Disconnect the + red post on battery. Jack up left side (DRIVER SIDE) secure vehicle with stands or blocking ! Spray the 3 bolts mounting the exhaust pipe to the manifold with a good pentrating oil.Unplug the 2 oxy. sensors on the pipe you'll be removing ( be careful not to break the clips on them) Get a thin sheet of metal cut it to fit up in front of fuel tank so no sparks can get on tank (GET A FULL FIRE EXTINGUISHER)( if you have a fuel leak you have to take care of that first!) after confiming there is no fuel or other combustibles in the area torch off the weld nuts on the rear side of the flanged pipe be careful not to damage flanges take a hammer and drive out bolts. Now move to the front of pipe room is limited i used several 3/8 drive extensions a swivel, 17 mm deep well 6 point socket with a 3/8 to 1/2 adapter hooked up to a 1/2 breaker bar.These nuts are selflocking tight little Bas*#% glow them with the torch be careful that the heat from your flame doesn't burn any wires or hoses! Key here is BABY STEPS heat it turn it heat it turn it after a full turn has been made heat it and hit it with the air rachet. You can now move the pipe down and back far enough to remove starter.Remove the 2 10mm bolts holding on shield. Remove the 2 14mm bolts holding starter to eng.for one you must slide wire loom out of the way to get on it. The starter wires one wire you must push down on top of connector to release it. the other wire is a 13mm i believe. Starter is gonna run about $150.00 Check gasket and flange area at manifold & gasket at flange at rear pipe. I applied red high heat silicone and reused mine. Used new nuts (Couldn't find flanged lockers just used regular mm nuts no washers) and bolts with neversieze. This should be done by a profesional ! LOL!
User Avatar

Wiki User

โˆ™ 2011-09-12 21:04:06
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: How do you replace the Starter on a 1996 Isuzu rodeo six cylinder?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace ignition lock cylinder Isuzu rodeo?

How I can replace ignition switch cylinder from Isuzu Rodeo?.


How do you fix a starter solenoid for a Isuzu Rodeo?

Replace Replace


How do you replace the Starter on a 1995 Isuzu rodeo 4wd?

Hi, How Do You Replace a Starter on a 1995 Isuzu Rodeo, V6, 3.2 liter engine? Does anyone know where the starter is? Help. How Do You Replace a Starter on a 1995 Isuzu Rodeo, automatic, 4wd, V6, 3.2 liter engine? Does anyone know where the starter is? Thanks alot.


Replace water pump on a 1994 Isuzu Rodeo?

replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo 6 cylinder


How do you replace the clutch slave cylinder on a 1997 Isuzu Rodeo?

take the cap off and roll another rodeo under it


Where is cylinder 1 on Isuzu rodeo?

cylinder one on a 2002 isuzu rodeo 3.2 engine is on center drivers side


Where is the starter on a 1992 Isuzu rodeo 4 cylinder engine?

Starter is on passenger side of motor underneath intake bolted to trans bellhousing.


1997 Isuzu Rodeo V-6 Starter Solenoid Removal what is the Procedure?

How to remove the starter from a 1997 Isuzu Rodeo 4X4 automatic


Where is the starter solenoid on a 93 Isuzu Rodeo?

mounted on the starter body


Where is the solenoid on 2000 Isuzu Rodeo located?

its built into the starter


How do you replace coolant temp sensor on a Isuzu Rodeo?

how do you replace coolant temp sensor on a rodeo


How do you replace the shocks on a 1997 Isuzu Rodeo?

How do I remove the front shock bottle pin of my Isuzu rodeo 2000

People also asked