On a 1998 Chevy Blazer, the parking brake switch is located on the top of the parking brake assembly. There are 3 bolts that hold the switch to the parking brake assembly.
That's what I am asking you. How do you replace a parking brake handle on an S-10 1996 Chevy Blazer?
How do you replace a break light switch on 1995 Chevy Tahoe
Make sure your brake lites work.If they dont replace brake lite switch
Replace and bleed line
Length of back brake line to replace. hole in it between front and back door
If nothing is holding the pedal down then the brake light switch is at fault.
Follow the below steps to replace the Brake Light Switch on Chevy Blazer:1) Open the Chevy Blazer's driverdoor, and move the driver's seat as far back as it will go. Lean under the dashboard with the flashlight, and shine the light on the brake pedal arm to locate the brake pedal switch.2) Unhook the brake pedal wiring pigtail from the Chevy's brake pedal switch by hand. Unbolt the old brake pedal switch from the mounting bracket using the box wrench set.3) Remove the old brake pedal switch by hand. Insert the replacement brake pedal switch into the brake pedal bracket. Bolt the switch in place with the box wrench set.4) Plug the brake wiring pigtail into the replacement brake pedal switch by hand. Readjust the driver's seat, and close the door. Hope this helps.
Well what do you know I solved the mystery mmyself it turns out after I paid to replace wheel cylinders and hoses and bleeding the brakes the cure was an $8.00 brake switch. Once I changed the switch the flashing brake light monster went away. So to anyone else who has a flashing brake light problem with your 89 Chevy S10 Blazer if you get a code 10 that is when the brake warning light flashes 10 times the fix is a new brake switch hope this helps someone.
You can try to reset your brake light switch by unplugging the brake light switch and plugging it back in. If that does not solve your problem you will need to replace the brake light switch.
Changing the brake light switch in your Chevrolet Monte Carlo is quite simple. The brake light switch simply plugs in and out.
Check the brake light switch.
Check the fuse, check the bulbs and check the brake light switch, it should be one of those.
The 1999 Chevrolet Malibu brake light switch can be found beneath the dashboard, next to the brake pedal. The brake light switch simply plugs in and out.
When the brakelite switch fails it fails to on. Replace the brakelite switch. Located under the dash on the brake pedal arm. You will see a push switch that is released when the brake is pressed. Just replace that switch.
Check the brake light switch on the brake pedal. Might have to replace it.
I can't turn the yellow brake or parking lights on my 1998 Chevy blazer off and it's draining my battery.Could you please tell me which fuse or switch I'd use to disable the front yellow lights? This is happening even with the car off.
It's just above the brake pedal, connected to the brake pedal arm. The switch comes out with two screws and the new one plugs in. But before you replace the switch, check the adjustment.
The relay is on the left side of the power brake booster/.
Brake Lights Stay on Unless the Brake Pedal is RaisedThis is usually caused by the brake light switch being out of adjustment in its physical distance to the contact point on the brake pedal arm.
The power brake booster on a 95 Chevy Blazer is replaced by draining and removing the master cylinder, unbolting the booster, and removing it from the vehicle. A new cylinder is then put in its place and bolted on.
7.99 at autozone you have to order it .
Directly above the brake pedal.
The brake light switch is bad, look on top of the brake pedal under the dash and you will see the switch, replace it and you will have brake lights.
It is quite easy to install the 1992 Chevy Lumina brake light switch. The brake light switch simply plugs in and out.