answersLogoWhite

0


Best Answer

go in behind it and there is a black retainer that you have to unscrew and then the bulb pulls out similar to how you replace tail light bulbs in older model vehicles go in behind it and there is a black retainer that you have to unscrew and then the bulb pulls out similar to how you replace tail light bulbs in older model vehicles if you remove the plastic strip on the top of the headlight under the hood...and then lift up on the two little levers the headlight will flip forward and give you EXTREMELY easy access to the bulb raise the hood. you will see a black cover under over the headlights and grille. remove it. then yo will see 2 black vertical bars that have a 45 degree bend in them that points toward the rear. pull up on the bars. there ar "key-hole" shaped holes in them so don't pull too hard. look down the bars and you shoud see 3 black rubber knobs. 1 on the inner bar(towards the grille) and 2 on the outer bar( towards the fender). align the knobs with the large hole in the bar. then just pull the headlight assembly straight forward. use a small flat bladed skrewdriver to lift up on the connector lock. BE VERY CAREFUL, Ford uses a brittle plastic in the connectors. take care not to break the lock or you will have to buy a new connector. pull the connector apart. turn the brown(or black)ring counter-clockwise. remove bulb. be careful not to touch the new bulb, it will burn out sooner or explode if you need to replace the turn signal bulb, just turn it to the left and pull the bulb out of the outlet. the corner marker are a little more tricky. the headlight has to be out, then you'll find a small hex screw in the corner, rermove it.then gently pull the housing straight out. turn the connector to the left and pull bulb out of the outlet. to put it in you have to make sure the wires are at the correct angle, then just reverse the process

User Avatar

Wiki User

โˆ™ 2006-02-15 23:08:14
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you replace the drivers side headlight bulb located on a 2001 Ford Ranger Edge?
Write your answer...
Submit
Related questions

How do you replace the headlight assembly located on a 1994 Ford Ranger?

detach the bulbs and remove the clips behind the headlight assembly


Where are the headlight adjustment screws located on a 1997 Ford ranger?

The headlight adjusting screws are accessible from the rear of the headlight, you have to open the hood to access them.


What steps do you take to remove and replace the master clutch cylinder of a 1992 Ford Ranger?

If you need to replace the slave cylinder it is located in the bell housing and the trans has to be removed. The clutch master cylinder is located on the firewall on the drivers side


Where is the low oil level sensor unit located on a 1994 ford ranger?

It should be located in the oil pan. On my ranger its on the drivers side.


Where is the icm on a 1992 ford ranger located?

The 1992 Ford Ranger ICM is located on the firewall in the engine compartment. The ICM will be on the drivers side of the firewall.


How do you adjust the headlight beam located on a 1994 Ford Ranger?

hey, you kick it but not to hard that you break it


Where is a fuel filter on a 1986 Ford Ranger located?

the fuel filter on a 1986 ford ranger is located on the inside of the frame on the drivers side in front of the gas tank.


How do you replace the fuel filter on a 1992 Ford Ranger?

where is fuel filter located on a 1992 ford ranger


Where is the fuel filter located on a 1989 Ford Ranger?

on the drivers side frame rail


Where is smog pump located on 85 ford ranger?

The 1985 Ford Ranger smog pump is located on the firewall in the engine compartment. The smog pump will be on the drivers side of the firewall.


Where is the fuel filter located and how do you replace it on a 1985 Ford Ranger?

It is located in the drivers side frame rail. It is hidden behind a metal debris guard. Twist off the black fuel bowl of the filter housing (after you have relieved the fuel pressure) and replace the disk filter and o-ring.


Where is the drl module located on 1994 ford ranger?

behind left headlight in front of battery. Has 5 wires to it.


How do you install headlight switch in 1991 Ford Ranger?

I need to know how to install a headlight swith in a 1991 ford ranger xlt


Where is the ignition module located on a 1989 ford ranger?

The 1989 Ford Ranger pickup truck ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


Where is the horn located on a Ford Ranger 1994?

under the inner fender of the left wheel drivers side


Where is your fuel filter located on a 93 ford ranger 30?

its mounted to the frame under the drivers seat


What fuse in a 91 ford ranger controls the fuel pump?

The fuel pump on a 91 Ford Ranger is controlled by the starter fuse and relay. This relay is located under the hood. It will be located by the fender on the drivers side.


Where is the egr valve located on a 1996 ford ranger?

drivers side behind ac compreesor on 4.0 model


Where is the fuel filter located on a 1997 Ford Ranger?

It's under the drivers side door, by the front axle


Where is the spout connector on a 94 ford ranger 3.0?

its located just forward of the battery and just behind the left headlight. it has pink wires.


Change headlight bulb ranger?

what is the bulb Walt for my 2004 ford ranger xlt 4.0


Where is the power distribution box on a 2004 Ford Ranger?

The power distribution box ( which is " live " ) is located in the engine compartment on the drivers side in a 2004 Ford Ranger


How do you clean the inside headlight lens on a Ford Ranger with the round cap on the inside?

To clean the inside headlight lens on a ford ranger just simply remove the cap and clean.


Where is the thermostat located and how do you replace it located on a 1996 Ford Ranger 6 cylinder?

follow the top radiator hose to the engine, remove it then remove the thermostat housing, remove the thermostat and replace it


Where is the the bleed valve on a slave cylinder on a 1993 ford ranger?

The bleed valve is located on the drivers side of the bell housing.