0
What else can I help you with?
How do you change breaks on a Pontiac aztek?
front or back? 2wd or awd? what year?
Where is the front 02 sensor of 2004 Pontiac Aztec?
The front O2 sensor of a 2004 Pontiac Aztek is located on the exhaust manifold, just before the catalytic converter. It is typically positioned on the driver's side of the engine, where the exhaust gases exit the engine. You may need to lift the vehicle for better access, as it can be somewhat difficult to reach without proper clearance.
What size is front axle nut on 2004 Pontiac aztek?
The front axle nut on a 2004 Pontiac Aztek typically has a size of 30mm. This nut is used to secure the hub assembly to the axle. Always ensure to use the correct tools and torque specifications when working on the vehicle.
Where is the engine coolant temperature sensor locater on a 2004 Pontiac aztek?
The engine coolant temperature sensor on a 2004 Pontiac Aztek is typically located near the thermostat housing, which is situated at the front of the engine. Specifically, it can be found on the engine block, often near the intake manifold. To access it, you may need to remove any obstructing components for easier visibility. Always consult the vehicle's service manual for precise location and replacement procedures.
How do you replace an alternator in a 2003 Pontiac aztek?
To replace the alternator you must tip the motor. by removing the motor mounts in front on the motor.just the two top ones and than roll the motor forward. that will give you enough room to remove the alternator
How do you replace the front left wheel speed sensor on a 2002 Pontiac Grand Am SE with ABS?
I have the exact same car and the exact same problem!
Replace a front hub assembly in a 2004 aztek?
To replace the front hub assembly in a 2004 Pontiac Aztek, first, safely lift the vehicle and remove the front wheel. Then, disconnect the brake caliper and rotor to access the hub assembly. Remove the hub assembly by unbolting it from the steering knuckle and disconnecting any associated wiring. Finally, install the new hub assembly, reassemble the brake components, and ensure everything is securely fastened before lowering the vehicle.
How do you replace ambient temp sensor on 2000 Pontiac Bonneville?
To replace the ambient temperature sensor on a 2000 Pontiac Bonneville, first locate the sensor, which is typically found near the front of the vehicle, often near the grille or bumper. Disconnect the wiring harness from the sensor and remove it from its mounting bracket. Install the new sensor by securing it in place and reconnecting the wiring harness. Finally, test the sensor to ensure it's functioning correctly.
What size is the front hub nut on a 2003 Pontiac Aztek?
The front hub nut on a 2003 Pontiac Aztek is typically a 30mm nut. It's important to use the correct size when working on the hub assembly to avoid damaging the nut or the components. Always refer to the vehicle's service manual for specific torque specifications and procedures.
Where is fuel filter located on 2004 Pontiac Aztek?
The fuel filter on a 2004 Pontiac Aztek is located along the frame rail on the driver's side of the vehicle, just in front of the rear axle. It is typically mounted on the underside of the vehicle, making it accessible for maintenance. To reach it, you may need to lift the vehicle for better access. Always ensure the fuel system is depressurized before attempting to replace the filter.
How do you replace front fender 98 Pontiac Bonneville?
How do you replace passenger side fender on a 1998 pontiac bonneville se
Where is the crank sensor located on 1990 Pontiac Sunbird?
I have a 1992 Pontiac Sunbird with 2.0 four cylinder in it, just found the crank sensor on it, to replace it. It is located on the FRONT side of the engine, below exhaust manifold and just above the A/C compressor. HOPE THIS HELPS SOMEONE ELSE!
