0
Some manuals can be found at the link below. A trimmer has an FS designation, but many manuals with A BG, FC or HS designation will do. The two most common engines in recent years have been the 4137 and 4140 engine families so watch for those numbers. If you have one of the newer 4-Mix engines, that is the 4180 engine and it would be the one that starts FC 90 and has FS 90, 100 and 110 in the list. If you have the old 4120 engine that Ryobi built, it is not there. See link below: this is the only place I know of with any service manuals for Stihl!
What else can I help you with?
How can I replace the pull cord on my Ryobi trimmer?
To replace the pull cord on your Ryobi trimmer, you will need to remove the housing covering the pull cord assembly, unwind the old cord, replace it with a new one of the same length and thickness, and then reassemble the housing. It's important to follow the manufacturer's instructions and use the correct tools for the job.
How do you fix a flooded stihl gas trimmer?
To fix a flooded Stihl gas trimmer, first, turn off the ignition switch and remove the spark plug. Pull the starter cord several times to expel excess fuel from the cylinder. Allow the trimmer to air out for a few minutes, then reinstall the spark plug. Finally, try starting the trimmer again, ensuring to use the choke correctly and not to over-prime.
How do you lubricate the shaft of a Stihl FS-46 trimmer and what lubricant?
To lubricate the shaft of a Stihl FS-46 trimmer, apply Reynolds lubricant to the shaft. Rotate the shaft and pull the converging wedge between the shaft and the bearing.
How do you repair pull cord on homelite trimmer?
The pull cord on a Homelite trimmer is repaired by removing the outer cover and pulling out the cord spool. A new line is then attached, wound around the spool, and put back in place.
How do you replace the pull cord on a ryobi trimmer?
first u need to remove the screws holdiny the pull cord housing then u remove it and pull the old cord out and hold it then remove the end of cord that has the knot to keep it in place wen u install new one do reverse but dont let the cord wheel go back
How do you replace the pull string on the Bolens BL110 gas trimmer?
how to replace pull wrope on bolens bl110
How do I replace the generator pull cord?
To replace the generator pull cord, first, remove the old cord by unscrewing the cover and pulling out the remaining cord. Next, thread a new cord through the hole in the cover and tie a knot at the end. Wind the cord around the pulley and reattach the cover. Finally, test the new cord by giving it a gentle pull to start the generator.
How do you replace pull cord bolens BL100?
To replace the pull cord on a Bolens BL100, first, remove the engine cover by unscrewing any bolts that secure it. Then, take out the old pull cord from the recoil starter assembly. Measure and cut a new cord to the appropriate length, thread it through the recoil assembly, and tie a secure knot. Finally, reassemble the cover and ensure everything is tightly secured before testing the pull cord.
How do you open a hood when the latch breaks?
Use pliers to pull cord or replace latch.
How do you start a stihl 041 AV?
To start a Stihl 041 AV chainsaw, first ensure the chain brake is engaged and the fuel mixture is prepared. Set the choke to the "cold start" position, pull the starter cord until you hear a pop or see signs of firing. Then set the choke to the "run" position and pull the starter cord again until the engine starts. Once running, disengage the chain brake and allow the saw to warm up.
How can you replace the trimmer line mac 2816?
Locate the trimmer head at the shaft. Remove debris in the head. Cut a 14-inch piece of the trimmer line and fold it. Place the spool against the spindle. Feed the ends of the line through the eyelets. Push the spool down and pull the trimmer line tight with your hands. Tighten the spool.
How do you fix a shower pull cord?
To fix a shower pull cord, first, ensure the power is turned off at the circuit breaker for safety. Remove the cover plate and inspect the cord for any frayed or broken sections; if damaged, replace the cord. If the cord is intact but stuck, gently pull on it to free any obstructions or lubricate the mechanism. Reassemble the components, and restore power to test the functionality.
