0
Threading the Wire
Place a box of twine or wire in each of the two holding brackets at the rear of the baler. Remove the cardboard discs in the center of each box and locate the end of the twine or wire on the inside of the coil.
2
Pass the end of the twine or wire from the right-hand box through the ceramic spool on the right-hand side of the ejection chute.
3
Pass the end of the twine or wire into the bottom opening of the right-hand threading needle. Pull the twine or wire out through the top of the needle.
4
Pull the twine or wire taut and tie it securely to the eyebolt, just ahead of the right-hand threading needle.
5
Repeat the procedure for the left-hand threading needle.If the twine or wire snaps when you engage the baler, you may have gotten the loose end from the outside of the coil instead of the inside. Check to ensure that the end of the twine or wire does not pass under or into the coil inside the box.
- If the wire snaps, you started the wrong end from the box of wire. Pay attention to the "Start this end" tag.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Where is the electical diagram for a John Deere F935 lawn mower?
need a color wire schematic for main wire harness
My john deere 50 won't run unless a hot wire from the battery to the coil?
use a key.
How do you thread a ford 532 wire hay baler?
Run the twine out of the twine box and through the guide next to the needle. Then run the twine through the needles and tie it off somewhere. When the knotter trips, it will inject the twine into the knotters and it will be threaded. If your baler has been sitting for awhile, it might take a few cycles for it to start knotting properly due to rust. for starters if it's a wire baler it doesn't have twine or knotters; it has wire and twisters. but it's true you thread it through the guide holes in balewire box, down through the sheaves, up over sheaves just before the needles and across the top of the needles then tie it off to the brace just like a twine baler. be careful, make sure it's centered over the top of the needles. after it makes a cycle you should be able to see if it picked up the wire and has held it in twisting grippers. it is held in these until the wire goes around the bale, then it should twisted and cut. make sure sheaves that wire goes through are lubricated with wd40 or something similar. i bought my 532 about five years ago and it does a good job. i think you can still get a manual for this baler from your ford ag dealer.
Wire diagram 314 John Deere?
Most John Deere dealers will print this off for you for free, at least they do in Ohio. Try this , I hope they will work with you .Just so you know ,if your having problems with the wiring the harness is not that expensive , Replace it and save your self time .
Where is the battery located on a John Deere 2555?
Find the starter and follow the heavy gauge wire from the starter. It will go to the starter relay or battery. If it goes to the relay then follow the heavy wire from the relay which will go to the battery.
What are the components of baler?
An input area, a compression chamber, hydraulic arms or rams, wheels, hydraulic cylinders, and tying mechanisms are all common industrial baler components (twine, rope, netting, wire, strapping, etc.).
Where is the spark-plug on a John Deere stz38?
On the front of the engine, Might be a little closer to the right. Just follow the big fat plug wire that's about 6 inches long.
Another name of single strand wire?
Another name that can be used for a single-strand wire is thread or strand.
Another name for a thread guide is?
Yarn guide / Wire guide
How do find the reason for no spark on a L100 john Deere?
Check the plug. If broken, replace it. If fouled clean it.Check your plug wire. If broken replace it.Check your battery. If dead, charge it or replace it.
How do you wire a bicycle dynamo?
EASILY. jUST THREAD THE WIRE THROUGH THE HOLES AS SHOWN IN THE INSTRUCTIONS THAT YOU CAN GET POSTED TO YOUR POSTAL ADRESS.
Why does your fuse keep blowing on your John Deere 190C riding mower when you try to replace it?
I hope you mean a 190C. Look for a broken or bare wire on the left side of the machine going toward the rear.
