0
An OR with one input inverted will be either "implication" or "converse implication" depending on your point of view. Given an OR with inputs "P" and "Q", You'd invert "P" to get implication. You'd invert "Q" to get converse implication.
In prose converse implication would be "P OR NOT Q".
What else can I help you with?
What is the difference between sampling gates and logic gates?
A logic gate is a computer circuit with several inputs but only one output that can be activated by a particular combinations of inputs, a diagram that shows the major gates can be found here.An example would be if you have 2 wires going to an AND gate and only 1 wire has a current (is on, 1) and the other one is 0, then your output would be 0 as you need wire 1 AND wire 2 to have a current, for the output to be 1, on.A sampling gate, on the other hand is a circuit that produces an output only when first activated by a preliminary pulse. So if you have a current going through a wire and through a sampling gate, your output would be 0, unless you program the sampling gate to let the current through.I'm sorry if this is a slightly plain answer, but if you would like more reading, then go to the Wikipedia.
How do you connect a logic gates to bread board?
Try to familiarize with the pin that the gate has. Know the right connection of your Integrated Circuit, make a review before putting any wire unto your bread board. Always double check if its in the right place to avoid any short circuit.
What is wire ANDing?
In digital logic, when two or more wires are ALL on, output is on. When any one wire is off, the circuit is off. Beyond that, you'll need to be a little more specific on the question.
Why are two converse sneakers hanging over a telephone wire inappropriate?
It is most commonly used to symbolize that a house is dealing drugs around them. It can also mean other things.
How do you make a switch?
you may make the switch by following ways :- 1. by using the flip - flops . 2.by using the logic gates according to your desire. you may also make switch by the mechanical process as follows:- 1.take two pcs. of wire 2.take a iron thin and small slide like plate 3.take a spring in the middle of the iron plate 4.attach the wire used to be transmitting in one end 5. press up and down for switching
How to operate a relay through two parallel relays?
To operate a relay ( I am calling "third relay") from two separate parallel control relays is called logic "or". Connect the power wire coming in to both of the paralleled relays' switch common contact. ( These relays are up to you to wire their coils and activate.) Depending on the logic required you will wire the third relay coil to the paralleled control relays normally open or normally closed contacts. That is: Do you you want the third relay to go on with the control relays activation or off?
Which of the following is important to have in a horse paddock Lots of prickles or Three or more gates or A reliable water source or Loose barb wire fences?
Lots of prickles = BAD - they may harm the horse Three or more gates = not BAD but why do you need more than one? A reliable water source = GOOD - horses need water Loose barb wire fence = BAD - it could tangle in the horses legs and injure them.
What security was used in concentration camps?
fences, electric fences, some had stone walls, human guards, guard dogs, lights, alarms, gates, barbed wire and collective punishment. To name a few
A wire diagram for the dump part of loadking belly dump?
A wire diagram for the dump part of a LoadKing belly dump trailer typically includes the electrical connections for the hydraulic system that operates the dump gates. It would show the wiring for the hydraulic pump, solenoid valves, and control switches, indicating how power is routed to operate the gates. Additionally, it may include safety features like limit switches and emergency shutoff connections. This diagram is essential for troubleshooting and ensuring proper operation of the dumping mechanism.
How many amps is 26 awg wire rated for?
A 26 AWG wire typically has a current rating of around 0.22-0.3 amps for power transmission in open air or an enclosed environment. This may vary based on factors like temperature and insulation material.
How much does a barbed wire fence cost per foot?
The cost of a barbed wire fence typically ranges from $1 to $3 per foot, depending on factors like the type of barbed wire used, the height of the fence, and installation expenses. Additional costs may arise from posts, gates, and labor if professional installation is required. Overall, the total price can vary significantly based on local materials and labor rates.
Could Japanese people leave the Japanese internment camps?
Of course they couldn't. Not only were the camps in the middle of nowhere, but they were surrounded by gates with barbed wire on top, and guards. It was pretty much a concentration camp without the killing. Most of the time.
