How is call flow in gsm Network?

Answer 1

The user keys in the phone number for
the landline subscriber and ..
Send Button
.. presses the Send button
Begin RR Connection Establishment
Call related information needs to be transported from the mobile phone to the Mobile Switching Center (MSC). This requires the establishment
of a Radio Resource (RR) connection to MSC. The first phase of the call setup just sets up this RR connection.
RR CHANNEL REQUEST
RR connection establishment is
triggered by sending the Channel
RACH
Request message. This message
requests the Base Station System (BSS)
for allocation for radio resources for the
RR connection setup. The mobile now
waits for an assignment on the Access
Grant Channel (AGCH). At this point the
mobile is listening to the AGCH for a
reply.
Note: The RR CHANNEL REQUEST is sent on a Random Access Channel (RACH). This is a slotted aloha channel that can be used at random,
without any coordination between the mobiles. Any mobile can transmit on this channel whenever it wishes. If two mobiles transmit on the
channel at the same time, their messages will be lost in a collision. The mobiles will detect the collision via a timeout and retransmit the
message after a random back off.
allocate
The BSS allocates a Traffic Channel
TCH
(TCH) to the mobile. The TCH allocation
assigns a specifies a frequency and a
timeslot on that frequency. After the
mobile receives this message, the
mobile shall only use the specified
resources for communication with the
mobile network.
RR IMMEDIATE ASSIGNMENT
The BSS transmits the radio resource
assignment to the Mobile via the AGCH
AGCH, Radio_Resource = (TCH, Frequency,
Timeslot), Time Correction, Frequency Correction
channel. The message also contains the
time and frequency corrections. The time
corrections allow the mobile to time it's
transmissions so that they reach the
BSS only in the specified slot. The
frequency corrections correct for the
Doppler shift caused by the mobile's
motion.
Apply the time and frequency corrections
Adjust the frequency and timing based
on the advice from the BSS. This step is
required so that transmissions from the
mobile reach the base station at the
precise time and with the correct
frequency.
Tune to the frequency and timeslot
The mobile detunes from the AGCH and
tunes to the specified radio channel.
RR SABM + MM CM SERVICE REQUEST
This is the first message that is sent
after tuning to the channel. The Mobile
TCH, SAPI = 0
initiates a LAPm connection with the
BSC by sending a Set Asynchronous
Balanced Mode (SABM) message. The
service request message meant for the
MSC is also sent in this message.

GSM Call Flow (GSM Originating Call)
Cell
Mobile Network
Fixed Networ
Mobile Station
Base Stations
NSS
PSTN
User
Mobile
BSS
MSC VLR
PSTN
13-Sep-08 21:38 (Page 2)
RR UA
The BSS replies with Unnumbered
Acknowledge (UA) to complete the
TCH, SAPI = 0
LAPm setup handshake
SCCP CONNECTION REQUEST + MM CM SERVICE REQUEST
The BSS receives the CM Service
Request message from the mobile and
SS7
forms a "BSSMAP COMPLETE LAYER 3
INFORMATION". The BSS then piggy
backs the message on the SCCP
connection request message
Check subscriber authentication
MSC checks if the subscriber has been
authenticated. In this case, the
subscriber has already been
authenticated, so the authentication
procedure is skipped.
Enable Ciphering
BSSMAP CIPHER MODE COMMAND
Since the subscriber has been
successfully authenticated, the MSC
initiates ciphering of the data being sent
on the channel. The channel is ciphered
so as so protect the call from
eavesdropping.
Expect ciphered data from the mobile
Ciphering on the radio link is enabled in
three steps. As a first step, the BSS
starts expecting ciphered data from the
mobile but continues to send data in
clear. Since the mobile has not been
informed about the ciphering, all data
received from the mobile will be in error.
RR CIPHERING MODE COMMAND
The BSS sends the CIPHERING MODE
COMMAND to the mobile. The mobile
mode = CLEAR
will be able to receive this message as
the transmission from the BSS is still in
clear.
Enable ciphering for received and transmitted
As a second step, the Mobile receives
data
the message and enables ciphering in
transmit and receive directions. This
action will result in all BSS data being
received in error. (The BSS is still
transmitting data in clear.)
RR CIPHERING MODE COMPLETE
Ciphering has already been enabled, so
this message is transmitted with
mode = CIPHERED
ciphering. The BSS will receive this
message as it is already expecting
ciphered data in the receive direction.
Enable ciphering of data transmitted to the
The third and final step in the ciphering
mobile
handshake. The BSS enables the
ciphering in transmit direction. From this
point on ciphering is enabled in both
directions.
BSSMAP CIPHER MODE COMPLETE
BSS replies back to the MSC, indicating
that ciphering has been successfully
enabled.
RR Connection Establishment Completed
At this point a connection has been setup between the Mobile and the MSC. From this point onward, the BSS is just acting as a conduit for
transporting the signaling messages between the Mobile and the MSC.
Call Setup
CC SETUP
The Mobile sends the setup message to
establish a voice call. The message
Dialed Digits
contains the dialed digits and other
information needed for call

GSM Call Flow (GSM Originating Call)
Cell
Mobile Network
Fixed Network
Mobile Station
Base Stations
NSS
PSTN
User
Mobile
BSS
MSC VLR
PSTN
13-Sep-08 21:38 (Page 3)
establishment.
CC CALL PROCEEDING
The mobile is informed that the call
setup is in progress.
Connecting...
At this point, the mobile phone displays
a message on the screen to indicate that
call setup is being attempted.
Mode Modify
allocate
The MSC allocates a voice circuit on one
Voice circuit towards BSS
the digital trunks between the MSC and
the BSS.
BSSMAP ASSIGNMENT REQUEST
MSC informs the BSS about the
allocated voice circuit. The call is also
Voice circuit
switched from signaling to voice.
RR CHANNEL MODE MODIFY
The BSS notifies the Mobile about the
changeover to voice mode.
RR CHANNEL MODE MODIFY ACKNOWLEDGE
Mobile acknowledges.
BSSMAP ASSIGNMENT COMPLETE
The BSS responds back to the MSC.
ISUP INITIAL ADDRESS MESSAGE
The MSC routes the call and sends the
call towards the called subscriber
SS7, Dialed Digits
ISUP ADDRESS COMPLETE MESSAGE The PSTN indicates to the MSC that it
has received all the digits and the called
SS7
subscriber is being rung.
CC ALERTING
The MSC informs the mobile that the
called subscriber is being alerted via a
ring
Alerting Tone
ISUP ANSWER
The called subscriber answers the call.
SS7
CC CONNECT
The MSC informs the mobile that the call
has been answered.
CC CONNECT ACKNOWLEDGE
Acknowledge the recipt of CC CONNECT.
Connected
Display that the call has been connected.
Conversation
Speech
The call has entered the conversation
phase. The speech path has been setup
between the mobile subscriber and the
land-line subscriber.
Call Release
End Button
The mobile subscriber hits End to clear
the call.
CC DISCONNECT
The mobile sends the disconnect
message to the MSC.
ISUP RELEASE
The MSC initiates release on the PSTN
side.
SS7
Disconnect Voice Path
The MSC disconnects the voice path and
also releases the voice circuit between
the BSS and the MSC.
free
Voice circuit towards BSS
CC RELEASE
The MSC informs the Mobile that it has
initiated call release

GSM Call Flow (GSM Originating Call)
Cell
Mobile Network
Fixed Network
Mobile Station
Base Stations
NSS
PSTN
User
Mobile
BSS
MSC VLR
PSTN
13-Sep-08 21:38 (Page 4)
ISUP RELEASED
The MSC informs the PSTN that the call
release has been completed.
SS7
ISUP RELEASE COMPLETE
The PSTN informs that call release has
been completed at its end.
SS7
CC RELEASE COMPLETE
Mobile indicates that the call has been
released.
RR Connection Release
BSSMAP CLEAR COMMAND
Call release has been completed, now
the RR connection is released by the
MSC.
RR CHANNEL RELEASE
The BSS initiates RR release with the
mobile.
BSSMAP CLEAR COMPLETE
The BSS informs the the MSC that the
RR connection has been released.
RR DISC
The mobile sends a disconnect message
to release the LAPm connection.
RR UA
The BSS replies with an Unnumbered
Acknowledge message.
free
The BSS releases the TCH channel.
TCH
Call Released Indication
Mobile goes back to the default display
to indicate that call has been completely
released.

ECE Charanjit.

Answer 2

Call flow can offer 3G is very much the same as any of the other telecommunications suppliers. They operate in the Kent area and will supply 3G if the facilities and signal strewth are available.