0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many Imperial gallons are in a 1 meter length of 102 mm id pipe?
A 1-meter length of 102mm inside diameter pipe has a volume of: 1.797 cubic Imperial gallons or 2.159 US gallons.
A one-meter closed pipe produces a sound whose wavelength is how many meters?
1 meter = 1/4 labda so 4x1=4 m 4 m
What volume of water is there in a meter of 22mm pipe?
The volume of water in one meter of a 22mm-diameter pipe is: about 0.1 US gallons.
What type of pipe thread sealant should you use?
Teflon tape is good. There is now a teflon liguid sealer also. The old pipe sealer is still good. I used a piece of radio solder last year to seal a water meter joint when I lost the meter seal. Be inventive.
How many square meters in a 10 linear meter pipe which is 12 inches in diameter?
This question cannot be answered sensibly. The required measure of the pipe is that of a volume which has dimensions [L3]. A square metre has dimension [L2]. Basic dimensional analysis teaches that you cannot convert between measures with different dimensions such as these without additional information.
How much water will 1 meter of 28mm pipe hold?
A 28mm round bin holds how much product
Can you join 1 inch copper pipe to 28mm copper pipe?
I have recently had to join a 1 inch steel water pipe to a new copper 28mm pipe. You can do this using a 28mm comression joint. 1inch is just uneder 28mm in diameter but the compression joint takes up the difference and works without fault or leaks.
How many liters of water in 1 meter of 4 inch pipe?
There need no be any water at all! The capacity of the pipe is 8.11 litres approx.
What is the equivalent diameter of copper to ppr pipe?
28mm
What is the internal diameter of 28mm copper pipe?
28mm will be the outside diameter. In the UK, depending on what BS standard the pipe is designed to, the thickness of the copper will be either 0.9mm or 1.2mm, the same as for 22mm pipe. assuming to thicker later type, then the internal diameter would be 28mm - (2*1.2mm) = 25.6mm
How many liters in a 100 millimeter pipe 1 meter long?
Assuming the pipe is 100% full then the volume will be the cross sectional area of the pipe times length. Vol = Pi/4 * (diameter)2 * (length) = (3.14/4)*(0.1 m)2*(1 m) Volume is approximately 0.008 m3. 1 cubic meter is 1000 liters so the volume would be about 8 liters.
How many liters in a 1m length of 100 m diameter pipe?
Volume of the pipe = (pai) (Diam) 2 (Length)/4 = 3.14 x 100 x 100 x 1 /4 = 7350 cubic meter 1 cubic meter = 1000 liter Volume in liters = 7350 x 1000 = 7 350 000 liters
What is the flow rate for 28mm copper pipe?
To provide an answer to this question the pressure of the fluid applied at the input end of the pipe must be provided.
How many liters of water in 1 meter of 3 inch pipe?
18.2415 Liter 3 inches=7.62CM 7.62CM=0.0762M 0.0762 squared=0.00580644 then that times pie (3.14)=0.0182415 cubic meters- this is your volume. 1000 Liter is equal to 1 cubic meter. 0.0182415 cubic meters * 1000=18.2415 Liters
How many inch meter is present in a single pipe?
The answer depends on the cross section of the pipe and its length.
How many liters in a 1 m length of .15 m diameter pipe?
about 17.7 liters if the pipe is 100% full. Volume of pipe = CA*Length Vol = (pi/4)*(dia.)2*(length) = 0.7854*(0.0225m2)*(1m) = 0.0177m3 1 m3 = 1000 liters, so the answer is 17.7 liters
How many liters in a one meter x 25 millimeter pipe?
L*pi*r2 = Volume , where L=100cm , r=(2.5cm/2) 100*3.14*1.752 = 961.625cm2 = 961.625mL = 0.961625L
