0
http://vats.likeabigdog.com/
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace vss on 97 sable 24 valve engine?
If by "vss" you are referring to the vehicle speed sensor... Removal - # Disconnect the negative battery cable. # Raise and support the vehicle. # Remove the catalytic converter Y-pipe. # Unplug the VSS electrical connector. # Remove the VSS protective heat shield. # Remove the retaining bolt from the VSS. # Lift the VSS out of the transaxle. # Remove the driven gear retainer and the drive gear.
Where is the speed cable located on a 2000 Chevy Malibu?
raise the vehicle,disconnect the electrcal connection from the vss. remove the mounting bolt and withdraw the vss from the transaxle case. replace sensor "O" ring.
How do you take out the vss on a 98 ford escort zx2?
Locate the VSS on top of the transaxle. It has an electrical connector to it. Disconnect the electrical connection. Remove the retaining clip and disconnect the speedometer cable. Pry the speed sensor out of the housing. Check the o ring for being bad. Installation is the reverse of this information.
How do you reset the computer on a 1995 Chevy Camaro?
Disconnect the battery for an hour, or so.
How do change speed sensor in a Chevy 2001 S-10?
Disconnect the electrical connection from VSS (Vehicle Speed Sensor), remove small bolt holding the VSS bracket in place, remove VSS by gently twisting and pulling out at the same time. Clean area and lubricate the "O" ring on the new sensor before installing it.
Where can a splice be made into the VSS in a 1995 3.4L Camaro for a navigation system?
It would be best in the wire to the sensor. You will need to solder and heat shrink the wire to prevent corrision.
How do you disconnect a horn on a 1994 Camaro?
I think the fuse is segregated, so, you could pull the fuse.
How can you isolate the vss vehicle speed sensor from the sensor buffer and where are they located on a 1992 camaro rs 305 with automatic transmission when your speedometer quits working?
If your speedometer is not working, or working intermittently and you want to isolate whether it's a faulty VSS or buffer box, try this: BEAR IN MIND THAT THIS IS ONLY FOR TBI EQUIPPED CAMAROS. Locate the buffer box. It is under the dash on the passenger side. You'll have to remove the lower cover to access it. The buffer itself is a printed circuit housed inside of a plastic case. On my Camaro, the plastic case is white. I've heard of others being yellow. There are two connectors on the buffer. Disconnect the small one (yellow and purple wires) get a voltmeter, set it to read DC voltage, connect to the plug (polarity doesn't matter). Take someone with you and go for a little drive. Have your ride around buddy monitor the voltmeter. If the VSS is sending out a signal, the voltmeter will register a small amount of voltage. It varies slightly depending on speed. If the voltmeter is not detecting any voltage, chances are that you have a faulty VSS. The VSS sensor is in the trans on a 92 camaro. If you have a tpi motor there is no buffer. The signal is sent directly to the ecm. From there it is sent to the speedometer and cruise control unit. What exactly are you tring to accomplish?
Where is the vss wire on a 2006 peterbuilt?
Goes from the VSS to the ECM. Find the VSS, and you can trace it from there.
How do you reset the computer on a 1998 Chevy Camaro?
Easy way is to disconnect the battery cables for about 30 minutes.
How to check and add transmission fluid to manual 93 ford escort?
Transaxle Fluid Level Check The transaxle fluid level should be checked only after the vehicle has been parked on level ground for some time. 1. Be sure the vehicle is on level ground and apply the parking brake. 2. Disconnect the electrical connector from the Vehicle Speed Sensor (VSS). 3. Disconnect the speedometer cable from the VSS. 4. Remove the retaining bolt and pry out the VSS. 5. Check the fluid level as shown. In the service manual figure shown full level at the upper border of VSS gear and low level at the bottom border of the VSS gear 6. If necessary, add transaxle fluid as explained in this section. 6.1 Place a funnel into the VSS mounting hole. 6.2 Add the specified transaxle fluid until the "full" level on the VSS is reached. Installation 7. Install the VSS. 8. Install the VSS bolt and tighten it to 8-12 N-m (69-104 lb-in). 9. Connect the speedometer cable. 10. Connect the electrical connector.
Where is the VSS located on a 1998 Honda Civic?
the VSS is right on top of the Transmission with a plug on top of the VSS
