Serpentine Belts
Chevy Corsica
DIY Projects
How To

How to put a belt on a 96 Chevy Corsica?

242526

Top Answer
User Avatar
Wiki User
2006-05-29 04:20:27
2006-05-29 04:20:27

i assume you mean new belt you need to remove upper motor mount to remove belt and pull tensioner up to release tension

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 96 Chevy Blazer does not have a timing belt.

User Avatar

Usualy the tensioner or idler pulley is spring loaded and can be pulled backwards allowing enough slack for the belt to slip on easily On a 1992-1996 Beretta/Corsica, the upper engine mount needs to be removed in order to remove/replace the serpentine belt. Replace the belt, and reinstall the engine mount.

User Avatar

My 96 corsica does the same thing, so maybe this will help: I have a small coolant leak, and I have to put more antifreeze in quite regularly. when my coolant level is too low, my heat stops working. try checking your coolant levels, remember to use universal or dexcool.

User Avatar

does not have a timing belt it has a chain

User Avatar

I just put a open end wrench on it, and stuffed my hand in

User Avatar

1 for each cylinder a 6 cylinder has 6 a 4 cylinder has 4 and so on.

User Avatar

It's on the corner of the steering wheel. With little horn signs. It's not in the middle of the steering wheel.

User Avatar

if it is like the 95 it is like a screw get a wrench and put it on the flat sides and turn

User Avatar

NO, The 1996 must have the 96 model 4L60E PUT BACK IN IT.

User Avatar

A 96 Corsica uses OBD2 as required by law for 96 model years. Use an OBD2 Scanner.

User Avatar

fuel sending unit broken wire or gauge is bad

User Avatar

The only governor I can think of is part of the automatic transmission the helps to control the shift points at which the transmission changes gear ratios.

User Avatar

There is a spring on the fuel door hinge that keeps the fuel door closed. I hope this info helps.

User Avatar

Not sure about the Corsica, but I know that there are unique differences in some of the parts between a 94 and 96 Grand Am. I was told by a salvage yard once, that the engine in a 96 Grand Am is different than that of any other Grand AM. To summarize, I was thinking of buying a used engine for my 96 and the salvage yard told me that the used engine would absolutely have to come out of another 96.

User Avatar

do you put timing chain on 3.1 96 Chevy lumina dot to dot

User Avatar

The brake lines on a 96 Corsica can be fixed by replacing damaged sections with new lines. This will improve braking and prevent catastrophic failures.

User Avatar

I'm assuming that you already have the serpentine belt off. its the smooth pulle, and bracket. located the pulley, and on either side there should be a bolt remove the bolts and pull off. steer the wheel to the right. for a better veiew.look under the panel, locate the tensioner it has a screw in the middle. you probably need a wrench.

User Avatar

on a 96 (3.1 V6) it's a side mount it is on the passenger side of the car on the side of the engine, very close to the fender. the tensioner wheel will accept either an open end wrench or a 1/2 inch or larger pull bar. You will need a pull bar to change the tensioner or the belt, you can rent them from many autoparts stores.

User Avatar

The rear aren't easy since you have the self adjusters and parking brake mechanisms to contend with. Get a manual from the parts sore.

User Avatar

just take the tires off the back and the hubs should be free to move. if not, try prying a little, but be careful.

User Avatar

how ofen do you change a timing belt on 96 excel

User Avatar

Bottom of the engine on the oil pan.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.