Chevy Impala
Nissan Sentra
Ford Expedition XLT
How To

How to remove the door panel on a 1989 Nissan Sentra?

171819

Top Answer
User Avatar
Wiki User
Answered
2006-03-07 16:57:30
2006-03-07 16:57:30

take it to a strret raceing shop!

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


How to Set timing on nissan sentra 1600cc 1989 model

The thermostat on a 1989 Nissan Sentra is on the front of the motor to the left. It is just below where the valve cover meets top of the manifold. The thermostat is enclosed in the radiator hose at that location.

1989 Nissan Sentra Wagon 5 Speed intermittently wants to die out. Unless I give it gas it will stall. It will start back up again, with the same problem until problem stops. No pattern to diagnose.

It is either on the compressor, the smaller ac line, or the accumulator.

Using a screw driver remove the screws from the door panel, remove the clips, and pull the panel away from the frame slowly. Remove any wiring connectors, and remove the panel the rest of the way.

Try going to www.kbb.com and enter the data. This will give you a good ballpark in which to work.

It is very easy. There are a couple screws holding the outer frame. take them out and u will see more scews take them out too. you can just pull it out now.

Using a screwdriver, remove all the screws from the panel, remove all the clips from the panel, and gently pull the panel from the frame. Remove and wire connectors between the panel and the frame, then pull the panel off the rest of the way.

Using a screwdriver, remove the screws and the clips that hold the panel to the door frame. Gently pull the panel, reach behind it and remove the wiring connectors, and the panel should come free.

You don't. 89 sentra does not have a timing belt, instead it has timing chain. I have the 1989 Nissan Sentra 1.6L 4-dr sedan. My timing chain needs to be replaced. It runs inside the motor. It is a big task for an auto mechanic to replace it. It will cost me at a *trustworthy* business $470 for part(s) and labor to replace it. Expect it to take a whole day for the car to be in the shop.

remove the large bolts between the door and the vehicle....

Using a screw driver, remove the screws and the clips holding the panel to the door frame. Pull the panel away gently and remove any wire connectors, then pull the panel off the rest of the way.

Are you asking about the trim panel above the glove box or the trim panel in front of the radio or the trim panel around the instrument cluster? Ask again telling us which panel you wish to remove.

Go to www.crutchfield.com and click on "car audio." You can plug in your car's year and model, and the site will tell you what fits.

On driver side under the dash by door fusable links are in engine compartment on driver side by fire wall

could be any number of things you need to list symptoms as to what it does when you try to start it or what it ran like the last time it was running

The fuse will be under the hood in a black box of fuses the lid of the box will have a diagram on the inside.

You need to remove the arm rest, and the power lock switche,and the mirror control. pop all the panel clips on the edge of the door panel with a scew driver. Than with the window down, lift up on the panel .

If a 1989 Nissan Sentra clutch pedal quit working and the car is now stuck in reverse, it will need to be towed to a repair shop to fix the clutch. The transmission may also be damaged due to it being stuck in reverse.

take off the case that covers the air filter and look for a black cable behind the intake. follow it to the air intake and it should be right there.

First remove the dashboard to access the heater box and core! Then reversal of strip down to rebuild.

A 1989 Accord Lxi fuel pump can be reached vial the service panel located under the rear seat. Remove the seats and panel to reach the pump.

HEY WHAZ UP----I'M NEW ON THIS SITE BUT CAN HELP YOU.I JUST BOUGHT MY 1991 MAXIMA THIS IS MY FIRST NISSAN AND HAVE HAD TO FIX ALLOT OF STUFF.BOTH THE FRONT PANELS AND THE BACK PANEL ARE ALLMOST THE SAME.YOU MUST REMOVE THE HANDLE ON THE ARMREST 2 SREWS HOLD IT IN.[TOP SCREW]pull THE ANGLED PLUG REMOVE THE SCREW UNDER THE DOOR RELEASE HANDLE THERE IS A RADIUSED COVER PANEL REMOVE IT AND AND YOU WILL EXPOSE 2 SCREWS REMOVE THEM . NEXT UNCLIP AND PULL OUT THE { SWITCH & DOOR RELEASE LEVER } PANEL .UN PLUG POWER WIRES.PULL ON EDGES OF THE PANEL STARTING AT THE BOTTOM AND WORK YOUR WAY TO THE TOP.YOU HAVE TO POP THE PLASTIC RETAINER PLUGS ONE AT A TIME.UN PLUG THE INTERIOR LIGHT ON THE PANEL AND YOU ARE DONE....IF IT IS A FRONT PANEL...YOU MUST REMOVE THE 2 FORWARD SCREWS THEY ARE COVERED BY 2 COLOR MATCHED PLASTIC CAPS .THEY ARE FORWARD AND ARE CONSEALED BY THE DASH WHEN THE DOOR IS CLOSED.ALL SCREWS ARE PHILLIPS #2.hope this helps you buddy mack


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.