answersLogoWhite

0

Stop the pool for a couple of days and let the stuff settle to the bottom, you will note a cloudy layer at the bottom of the pool, carefully hand vacuum it to waste don't put it through your filter.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

What are the advantages of flocculent vs clarifier for clearing up pool water?

From what I gather from reading the back of the bottle of Clarifier that I use in my pool a Clarifier is a Flocculent. The clarifier contains a polymer that attracts the smaller particles floating around in the pool that are too small to be filtered through some filtration systems. As the clarifier attracts the smaller particles it becomes large enough for the filtration system to filter it out of the water thus clariying the pool water.


How much of pool water is too much to drink?

any


How do you use water clarifier?

Not too often as it tends to block up filters unles you vacuum to waste.


Clear a cloudy pool when the chlorine is high and pH range is normal?

# Test the swimming pool water for Combined Chlorine, pH, Alkalinity and Calcium Hardness. The two areas that are most likely to cause cloudy pool water are the pH and the Calcium Hardness. # If the pool chemical levels are not within the following suggested ranges, adjust the chemicals and run the pool filter system for 12-24 hours before re-testing. Free Chlorine: 1-3 ppm, pH: 7.2 - 7.6, Alkalinity: 90 - 120 ppm and Calcium Hardness: 200 - 350 ppm. # If all the pool chemical levels test in range, the cloudy pool water is caused by fine debris suspended in the pool water. You should backwash or clean your pool filter following the manufacturer's instructions, and run the pool filter system continuously for 24 to 48 hours. # If the water conditions have not significantly improved you should add a clarifier pool chemical to the pool water to help your pool filter remove the fine debris from the water. Continue filtering for 12 to 24 hours. # If the water conditions have not significantly improved you should add a second dose of clarifier, or a stronger clarifier chemical and continue to run your filtration system. # Sometimes a pool can be too cloudy for a clarifier. If this is the case you will have to move up to a floc. This will drop any suspended particles to the floor so you can vacuum it to waste. = It is common for pool water to become cloudy immediately after adding products to adjust the pool pH or Alkalinity. = If your pool water became cloudy within 6-8 hours of adjusting the pH or Alkalinity, continue circulating your water and it should clear within 24 hours as the water adjusts to the CHANGES YOU'VE MADE Suhail IsmailGENTECH UAE


What happens if there is too much calcium in your pool water?

If there is too much calcium in your pool water, it can lead to scaling on pool surfaces and equipment. This can affect water flow in pipes, reduce the effectiveness of sanitizer, and create cloudy water. It is recommended to maintain calcium hardness levels within the recommended range to prevent these issues.


How can you fix your pool if it is a really dark green after putting chlorine in it yesterday?

um... i would have to say, empty the water (if you can) then clean the pool spotless. Make sure all the tubes (jets) and filter is cleaned out and spotless again. then fill it up with clean water. run it for a day or two and then add the chlorine or and other chemicals you want. (That's the best i can say) or get a new pool.


What causes skimmer basket in pool to turn black?

Too much iron in the water


What do you do if you have too much salt in your swimming pool?

Drain some water out, a little at a time, and add fresh water.


Whats the remedy for Swimming pool being too salty?

drain some of the water out of the pool and replace with fresh water it would probably pay to work out how much to salty so you can work out how much water to drain.


What happens when an inflatable pool has too much water?

they will usually overflow, but in some cases they will pop.


What do you do if you put too much algae remover in pool?

If you accidentally put too much algae remover in your pool, the first step is to dilute the water by adding more fresh water. You can also run your pool's pump and filter system to help circulate and dilute the chemical. It's important to monitor your pool's water quality closely and consider testing it after a few days to ensure it is safe for swimming.


What can you do if your swimming pool has too much cooper?

Cooper or coPPer ? Too much cOOper , then ask Cooper to get out of the pool !!