0
If you have a 125 amp breaker box on the pole with a 125 amp breaker going to your house and you get a hot tub that needs a 60 amp GFI breaker would that overload the box?
Wiki User
∙ 14y ago
It depends on what else you are running in the house. Add up your amperage to see if it is more than the 125amp rating. Which should be below 105 amps constant to keep from overheating the main breaker. If you are not running a big central ac system or a electric oven and water heater you should have no problem running the hot tub.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Can you use 14-3 wire on a 20amp breaker?
No. A 20 amp breaker needs 12 gauge wire.
How much does a shunt trip breaker cost?
The cost of a shunt trip breaker depends on the amperage and number of poles the circuit connected to it needs. The cost of the shunt trip over a conventional breaker is substantially more.
How many 20amp outlets in commercial building per circuit?
All depends on how big your main breaker is and what size wire you are using,one 20 amp outlet needs #12 wire not more than 50feet away from main breaker
What makes a circuit breaker go bad?
A circuit breaker can go bad from being tripped too many times. Many people don't understand that the tripping of a circuit breaker indicates a problem that needs to be corrected. They usually just reset the circuit breaker, leading to a very common second (or third, or fourth) trip. Circuit breakers tripping are for the prevention of fire due to excessive heat in the circuit. They're not supposed to be tripped repeatedly. This can wear the breaker out. Believe it or not, I've also seen circuit breakers fail to re-energize after being turned off. I speculate this was actually caused by the breaker never having been cycled (it was a main breaker), and the time elapsed since it was installed. Electrical equipment doesn't last forever. It's the same as anything else.
Why would plugging in an AC unit in a wall receptacle cause the fuse to blow or breaker to trip?
Is the receptacle a 110 or a 220 outlet? If it's a 110, it needs to be a 220. Are there other appliances, lights, etc. wired on the same outlet? If so, you may have to re-wire so that no other appliances, lights, etc. are wired into the same breaker. Usually the larger appliances such as air conditioners, central heat systems are wired to a separate breaker or fuse.
What dangers are associated with overloading plug sockets?
You can overload the circuit, causing a heavy load on the breaker. If the house wiring is old, it can build up heat, espeacially in an attic and create a "hot-spot" potentially causing a fire. Any microwave of 1,000 watts or larger needs to be on its own breaker. A curling iron or blowdryer can overload a circuit in your bathroom, and trip a breaker if it is being shared with other appliances on the same breaker. Always consult an electrician if your having troubles tripping breakers or blowing the older-style glass fuses in your house.
If you have a 100-amp breaker box on the pole with a 100-amp breaker going to your house and you get a hot tub that needs a 60-amp GFI breaker would that overload the box?
That's pushing it but it can work. It depends if you have central A/C, electric range, water heater, etc. Those are your amp suckers. You'll need to be mindful when operating the hot tub; not running the dryer, oven, or other large appliances.
Your breaker won't stay on and continues to flip when ac unit is on i've changed circuit breakers out didn't work then upped them from 40 to 50 what should you do?
Please call an electrician before you burn your house down! Changing a 40A breaker to a 50A breaker will eventually melt your wire's insulation and start a fire if it continues to trip. I would say you should change it back, but you should let the electrician do that. There is a short or overload in that circuit, which needs to be corrected before you attempt to reapply power. Circuit breakers are not there to make your life harder, they are there to make your life longer! Have a professional electrician correct the short or overload and then replace the breaker with a properly rated breaker before energizing the A/C unit.
Every time you vacuum you blow the breaker in your house can you change the breaker?
Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.
What is the rips training principle?
recovery individual needs progressive overload specificity
Why does the fuse box in my house make a clicking noise when the heater clicks on?
The clicking noise you are hearing could be the heater is overloading the breaker and it is on the verge of tripping This could be caused by the heater being to large for the circuit. Check the amperage rating on the heater and the rating on the breaker It also cold be the circuit breaker is going bad and needs to be replaced by a qualified electrician These are 2 possible answers you also could have a bad (loose) electrical connection some where in the circuit
Can you use 14-3 wire on a 20amp breaker?
No. A 20 amp breaker needs 12 gauge wire.
What does RIPSR stand for?
Rest and recovery Individual needs Progressive overload Specificity reversibility
Where is main breaker switch?
a circuit breaker trips on overload,if this breaker has tripped many times it may be worn out,if there is a overload happening the breaker is doing it s job keeping you safe.Main breaker needs to be replaced when your meter has been pulled(removed from metersocket)Have a electrician look at it and verify problem, you should not attempt to change out yourself it will be live.......
What circuit breaker is interchangeable with Bryant?
To answer this question the type of breaker you want to exchange needs to be stated, bolt in or plug in.
What actions to be taken should a main generator circuit breaker stay connected?
I don't understand the question. <<>> If your generator's main breaker does not trip when an overload occurs on the generator's output the breaker's trip setting needs to be looked at. Usually the molded case breaker's face cover can be removed. This will allow you access to the trip settings. Set the overloads to the maximum generator's output. The short circuit setting should be set at 250% of the maximum generator output. If these parameters can not be met on the existing breaker there might be a chance that the breaker has been changed out at some point in time and the wrong breaker was installed at that time. This scenario happens quite frequently on remote operations where the service has to be maintained and the site doesn't have a second back up generator. The site supervisor usually says "just make it work".
What cause circuit breaker to trip when refrigerator plug in?
If you can plug the fridge into another outlet and it comes on, then the issue is either a bad outlet connection or the circut breaker may be going out and needs replacement. Try the fridge on another outlet 1st. If it trips that one too then there is a short in your fridge.
