No, the wide prong is neutral it is the white wire.
The narrow prong is hot it is the black wire.
The round prong (in a 3 wire plug) is safety ground it is the green wire.
The equipment grounding conductor is attached to the rounded prong in a three prong plug. Electrical work is dangerous, call a qualified electrician to install. Improper wiring could lead to personal property damage, you or someone else being injured or killed!
The ground prong (usually of a male plug) is a metal tab or rod connected to the conductor which is to be grounded.
Dryer plug three to fourOpen up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
If you are in north America, black and red go to the main prongs and white to the ground (round prong) . Black and red can be on either main prong.
Yes this is possible and for safety's sake highly recommended. Instructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the centre. From the centre wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
The equipment grounding conductor is attached to the rounded prong in a three prong plug. Electrical work is dangerous, call a qualified electrician to install. Improper wiring could lead to personal property damage, you or someone else being injured or killed!
Black wire to the gold screw, white wire to the silver screw, green wire to the round or U shaped prong screw.
The green wire is for ground. You can attach that to any metal part of the frame. The red is the active and coincides with the lefthand prong into the plug and the black in this case should be the Neutral and ciocides with the right prong into the plug as seen standing behind the plug.
On a British plug it is the earth pin connected to the earth wire. This is safety feature to stop electric shock
Because - the 2-prong socket is NOT connected to earth !.. Any fault in the appliance - could result in electrocution.
The ground prong (usually of a male plug) is a metal tab or rod connected to the conductor which is to be grounded.
The two prong electrical plug and outlet was invented by David Brown. i know
No you can not you will need to replace the plug with a 4 prong the same as the style of your oven and change your breaker to the correct Amp for your style of 4 prong plug
Dryer plug three to fourOpen up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
If you are in north America, black and red go to the main prongs and white to the ground (round prong) . Black and red can be on either main prong.
Yes this is possible and for safety's sake highly recommended. Instructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the centre. From the centre wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
Ground wire