0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Who profits from Leo Tolstoy royalties?
Tolstoy's Estate
When did the royalties of Spain sponsor Columbus to have his expedition?
In 1492, they finally sponsored him!
Who were the parents of Chief Sitting Bull?
His father was called Jumping Bull and his mother was named Her-Holy-Door.
What is the brightness of a star measurable by a scale called?
It is called the magnitude scale. It is a log scale.
What was George Washington's largest flaw?
Jumping
What is a jumping sliding sport?
soocer/football
Is a blood glucose sliding scale a ratio-scale measurement?
no
Motion used in basketball?
Running. Jumping. Sliding. Walking.
What is a rolling off-set?
a sliding scale
Where in Seattle can I get grief counseling on a sliding scale fee?
Seattle has a Therapist Referral List at www.spu.edu/depts/scc/SeattleTherapistReferralList.htm. Quite a few on the list accept the sliding scale fee.
Are there different types of music royalties?
There are five types of music royalties. These royalties include; Mechanical licenses and royalties, Performance rights and royalties, Synchronization rights and royalties, Print rights and royalties, and Foreign Royalties.
Where are some residential treatment centers that are open to the public and charged on a sliding scale?
MONDANARO-BASKIN CENTER at 516 Chestnut St. Santa Cruz, CA 95060 offers a sliding scale. Call them at (831) 423-9015
What are desert animals that eat a jumping cholla?
Only a few insects such as scale insects and cochineal bugs will attack a jumping cholla.
Who are penguins enemies and how does it protect itself?
this is around but penguins enemies are killer whales, and sharks they protect themselves by sliding into holes, jumping into the water, and sliding down ice hills away from ledges.
What are the 7 locomotors of gymnastics?
The seven locomotors of gymnastics is running,walking,skipping,trotting,flipping,sliding,and hopping(jumping).
How do you use vernier?
Instructions on useThe Vernier caliper is an extremely precise measuring instrument; the reading error is 1/20 mm = 0.05 mm.Close the jaws lightly on the object to be measured.If you are measuring something with a round cross section, make sure that the axis of the object is perpendicular to the caliper. This is necessary to ensure that you are measuring the full diameter and not merely a chord.Ignore the top scale, which is calibrated in inches.Use the bottom scale, which is in metric units.Notice that there is a fixed scale and a sliding scale.The boldface numbers on the fixed scale are centimeters.The tick marks on the fixed scale between the boldface numbers are millimeters.There are ten tick marks on the sliding scale. The left-most tick mark on the sliding scale will let you read from the fixed scale the number of whole millimeters that the jaws are opened.In the example above, the leftmost tick mark on the sliding scale is between 21 mm and 22 mm, so the number of whole millimeters is 21.Next we find the tenths of millimeters. Notice that the ten tick marks on the sliding scale are the same width as nine ticks marks on the fixed scale. This means that at most one of the tick marks on the sliding scale will align with a tick mark on the fixed scale; the others will miss.The number of the aligned tick mark on the sliding scale tells you the number of tenths of millimeters. In the example above, the 3rd tick mark on the sliding scale is in coincidence with the one above it, so the caliper reading is (21.30 ± 0.05) mm.If two adjacent tick marks on the sliding scale look equally aligned with their counterparts on the fixed scale, then the reading is half way between the two marks. In the example above, if the 3rd and 4th tick marks on the sliding scale looked to be equally aligned, then the reading would be (21.35 ± 0.05) mm.On those rare occasions when the reading just happens to be a "nice" number like 2 cm, don't forget to include the zero decimal places showing the precision of the measurement and the reading error. So not 2 cm, but rather (2.000 ± 0.005) cm or (20.00 ± 0.05) mm.thank you from assven q
How do you use vernier caliper?
Instructions on useThe Vernier caliper is an extremely precise measuring instrument; the reading error is 1/20 mm = 0.05 mm.Close the jaws lightly on the object to be measured.If you are measuring something with a round cross section, make sure that the axis of the object is perpendicular to the caliper. This is necessary to ensure that you are measuring the full diameter and not merely a chord.Ignore the top scale, which is calibrated in inches.Use the bottom scale, which is in metric units.Notice that there is a fixed scale and a sliding scale.The boldface numbers on the fixed scale are centimeters.The tick marks on the fixed scale between the boldface numbers are millimeters.There are ten tick marks on the sliding scale. The left-most tick mark on the sliding scale will let you read from the fixed scale the number of whole millimeters that the jaws are opened.In the example above, the leftmost tick mark on the sliding scale is between 21 mm and 22 mm, so the number of whole millimeters is 21.Next we find the tenths of millimeters. Notice that the ten tick marks on the sliding scale are the same width as nine ticks marks on the fixed scale. This means that at most one of the tick marks on the sliding scale will align with a tick mark on the fixed scale; the others will miss.The number of the aligned tick mark on the sliding scale tells you the number of tenths of millimeters. In the example above, the 3rd tick mark on the sliding scale is in coincidence with the one above it, so the caliper reading is (21.30 ± 0.05) mm.If two adjacent tick marks on the sliding scale look equally aligned with their counterparts on the fixed scale, then the reading is half way between the two marks. In the example above, if the 3rd and 4th tick marks on the sliding scale looked to be equally aligned, then the reading would be (21.35 ± 0.05) mm.On those rare occasions when the reading just happens to be a "nice" number like 2 cm, don't forget to include the zero decimal places showing the precision of the measurement and the reading error. So not 2 cm, but rather (2.000 ± 0.005) cm or (20.00 ± 0.05) mm.thank you from assven q
