Cars & Vehicles
Brake Pads and Rotors
Ford Windstar
Dodge Dakota

Right rear and which front brake do you bleed on 98 windstar?

121314

Top Answer
User Avatar
Wiki User
Answered
2007-11-01 01:26:12
2007-11-01 01:26:12

You're supposed to bleed all four brakes or you really arent doing anthing, you could also cause improper and uneven wear on the brake pads them selves

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions


You start at the brake farthest from the master cylinder. right rear, left rear, right front, left front.You start at the brake farthest from the master cylinder. right rear, left rear, right front, left front.


Did you bleed the entire brake system? First must bleed the rear right, the rear left, then front right and then front left. Don't ask me why but it is what it is. I have a 74 VW Bug



always use Honda Heavy Duty DOT 3 Brake Fluid. 1. make sure brake fluid level in reservior is at MAX 2. attach a length of clear tube to the bleed screw 3. have someone slowly pump the brake pedal several times, then apply steady pressure 4. loosen the left front brake bleed screw, loosen brake bleed screw to allow air to escape system. then tighten the bleed screw. 5. repeat procedure for every wheel until air bubbles no longer appear in fluid Sequence: Front left, Front Right, Rear Right, Rear Left 6. refill master cylinder reservoir to MAX


The brake for the front tire is the lever on the right side in front of the throttle. The brake for the rear tire is the little lever in front of your right foot peg.




You remove the wheels, remove the brake caliper and the rotor is then free .


Start bleeding off air from the futhest point away from the brake master cylinder and work towards the front wheels...if this does not help jack up the rear of the vehical and bleed again as air rises


I'm finding it hard to stop i think i need to bleed or tighten up the front brake HELP?


you need to bleed the brakesif you have air in rear you will also have air in front. to bleed you start at wheel furtherset from the brake fluid resevoir, then next furtherest, then 3rd furtherest then closetthat being said usually means rear right wheelrear left wheel,front right wheelfront left wheel


right rear ,left rear, right front ,left front.


My 92 Silverado right front brake sticking why


why after changing my front brakes on my Nissan altima,my brakes peddle got really soft YOU FORGOT TO BLEED YOUR BREAK LINES~! GO TO AUTOZONE, OR PEPBOYS OR ADVANCED AUTOPARTS AND GET A BRAKE BLEEDER KIT..THEY ARENT EXPENSIVE AND ALLOW YOU TO BLEED YOUR BRAKE SYSTEM ON YOUR OWN.


Could be a restricted/damaged brake hose or brake line on the left front.


Always best to bleed both sides if you change a brake line. EG: Both front or both rear.


blled both front and rear in this order Passenger Rear, Driver Rear, Passenger Front, Driver Front.


The old standard procedure was to start with the right rear, then left rear, then right front, then left front.


Facing the engine from the front of the vehicle, the battery is located in the right, front corner.


Remove the tire and wheel. Remove the brake pad springs. The brake pads will come off. Reverse the process to install the new brake pads.


There may be air in the brake system. Bleed the brakes and see if this helps. Bleeding the brakes requires two people, a quantity of new brake fluid, and wrench the correct size to open bleed valves on brake plates. The brake plate is the flat plate that the brake mechanisim is mounted on, and has a hose coming to it from the body of the car. The hose carries the pressure from the master cylinder to the individual wheel cylinders, and where it connects to the brake plate there is usually a bleed valve, which is a hexagonal piece of metal with a hole in it. When the bleed valve is loosened, it allows brake fluid to drain from the system. If no one is in the car with their foot pushing the brake pedal to the floor, air will enter the brake system through the bleed valve. So, have someone in the car who can push the brake pedal down, open the hood, and remove the cover from the brake fluid reservoir on top of the master cylinder. Have the brake pedal pushed down slowly (to keep the brake fluid from splashing all over the place. Be careful, brake fluid is highly corrosive!) as the bleed valve is opened, and held down until the bleed valve is closed. Repeat this procedeure three times, and then check the fluid level in the reservoir. Add fluid if necessary and go to the next wheel, which should be the left rear, as you want to start with the right rear, seeing as it is the furthest from the master cylinder. Work the right front after the left rear, and the left front last.



Does this Blazer have four wheel disc Brakes? NEW ANSWER: There's no reason to bleed brakes if you did not open the system.( where brake fluid came out )


There's a bleeder on all four wheels. You would start on the back, most likely back right, passenger side, then drivers side, then front right, front left, working farthest from the brake fluid reservoir to the closest.


Bleed theÊbrakesÊstarting with the right rear, left rear, right front, then left front. If the boosterÊwas gone, you would hear air leaking out of it when you pressed the pedal down.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.