If the toilet is sitting solid on the floor, you don't need to. I would use latex instead of silicone because if you should ever have to pull the toilet, it would be much easier. One reason not to seal it down would be if the wax ring should ever fail. You could have a lot of damage to the floor before you noticed the leak.
Depends on whether you already purchased it and whether other parts are needed. If you have the toilet, a Kant leak, a wax seal,FLEXIBLE toilet supply, and the (nuts,bolts and washers) for screwing the toilet to the floor flange, plumber should not charge more than one hour of his rate to install it. Make sure the plumber does NOT silicone around the toilet. If there is a leak from the wax seal under the toilet and it is siliconed, the water stays under the toilet and rots the floor, if you are on a wood floor.
To raise a toilet bowl off the floor, you can use a toilet riser or spacer, which fits between the toilet base and the floor. First, turn off the water supply and disconnect the toilet from the waste line. Then, remove the toilet by unscrewing the bolts and lifting it off, place the riser on the flange, and reinstall the toilet on top of it. Finally, reconnect the water supply and check for leaks.
To seal a toilet to the floor, you typically use a wax ring, which creates a watertight seal between the toilet base and the flange on the floor. Additionally, you can use caulk around the base of the toilet for added stability and to prevent water from seeping underneath. Make sure the surface is clean and dry before installation for the best seal.
The drain from the toilet to the main drain is plugged and the branch to the shower is not. If the main floor toilet flushes, it is between the two toilets and not between the house and the sewer.
No, it is not recommended to glue the toilet closet flange to the pipe. The flange should be secured to the floor using bolts or screws, and the toilet is then secured to the flange using wax rings or sealing gaskets. Gluing the flange to the pipe can make it difficult to remove or replace the toilet in the future.
Depends on whether you already purchased it and whether other parts are needed. If you have the toilet, a Kant leak, a wax seal,FLEXIBLE toilet supply, and the (nuts,bolts and washers) for screwing the toilet to the floor flange, plumber should not charge more than one hour of his rate to install it. Make sure the plumber does NOT silicone around the toilet. If there is a leak from the wax seal under the toilet and it is siliconed, the water stays under the toilet and rots the floor, if you are on a wood floor.
A toilet may leak from the bottom due to a damaged wax ring or a loose connection between the toilet and the floor. To fix this issue, the wax ring should be replaced or the toilet should be resealed to the floor.
Silicone would be advisable around the wax ring. In addition take silicone and put it where the floor and wall meet. This should be hidden by quarter round or shoe. This is so if the toilet were to over flow, the water would not be able to roll under the boards.
Yes, the toilet flange should be flush with the floor when installing a toilet to ensure a proper and secure fit.
To effectively use silicone around the toilet base, first clean and dry the area thoroughly. Apply a continuous bead of silicone around the entire base of the toilet, ensuring it is evenly distributed. Press the toilet firmly onto the floor to create a secure seal. Wipe away any excess silicone and allow it to dry completely before using the toilet. This will help prevent leaks and ensure a tight seal.
Yes, a toilet leaking from the floor can be fixed by replacing the wax ring seal between the toilet and the floor. This involves removing the toilet, replacing the wax ring, and reseating the toilet properly. It is recommended to seek professional help if you are not experienced with plumbing repairs.
If it's leaking between the toilet and the floor, you put the wax ring in wrong. If it's leaking between the toilet and the tank, you need to replace the gasket.
To secure a toilet flange to the floor, it is recommended to use corrosion-resistant screws, such as stainless steel or brass screws, that are at least 1.5 inches in length. These screws will provide a strong and durable connection between the flange and the floor.
To tighten a toilet to the floor properly, first ensure the toilet is properly aligned with the floor drain. Use a wrench to tighten the bolts at the base of the toilet, alternating between each bolt to ensure even pressure. Be careful not to overtighten, as this can crack the toilet base. Finally, use a level to ensure the toilet is sitting evenly on the floor before sealing the base with caulk.
on the floor between the toilet and stand.
Unless it is a very strange arrangement, turning off the toilet on the first floor should only shut off the water to that toilet. It should have no effect on the upstairs shower.
A toilet floor flange is a piece of plumbing that connects the toilet to the floor and the sewer pipe. It provides a secure base for the toilet to be bolted onto, ensuring stability and preventing leaks. The flange also helps to create a proper seal between the toilet and the sewer pipe, preventing odors and wastewater from escaping. Overall, the floor flange is essential for the proper installation and stability of a toilet.