Car Fuses and Wiring
Starters and Ignition Systems
Ford Explorer XLT

Truck blows fuse for ignition when turning key to start?

303132

Top Answer
User Avatar
Wiki User
2011-09-13 15:50:28
2011-09-13 15:50:28

coil wires are crossed, you are sending juice to the negative lead when you hit your key

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

By turning the ignition key...

User Avatar

With a key, by turning on ignition

User Avatar

may be a bad starter..... or if the engine is cranking with no start it could be the ignition wires

User Avatar

more than likely is the ignition module. What year?

User Avatar

For Ignition. Your car will not start if this fuse blows, generally if there is a short.

User Avatar

after truck warms up will be hard to start,module may even start turning white colored make sure you are getting 12 volts to the module from the ignition also good luck

User Avatar

No, if it starts on its own without you turning the ignition switch then the ignition switch is defective.

User Avatar

I had a similar problem on a Ford truck and it turned out to be the ignition switch. The truck would start just fine but when I released the ignition key the truck would die. I replaced the switch and problem was gone.

User Avatar

generally , cranking an engine is done with igniton where turning is done by hand with the ignition off so as it will not start

User Avatar

Well somethings i need to know? Is the truck engine turning over and just not starting? If the truck is turning over i would first off guess either gas or elelctrical problems. If the starter is not turning the engine over, then i would point at the starter relay (you should hear that click when you turn the key). Also if you find that the relay is fine and it is just not clicking then i would look at the ignition switch on the steerin column. . ) Also, it may be the ignition control module. If the engine turns, but no spark, this could be the ptoblem also. Good Luck!

User Avatar

When owning a four wheeler it is important to know how to start it. This is done by turning or flipping the ignition switch on the vehicle.

User Avatar

I've had to resolve this issue by turning the steering wheel and playing with the key. You can try to start the truck and then quickly turn it off to get the key to come out as well. My problem ended up being a shift solenoid that was sticking and telling the truck that it was still in gear.

User Avatar

It is possible that a Ford Transit might not start if the key was left in the ignition in the on position. The battery is probably dead, if turning the key produces no noise at all.

User Avatar

More than likely it is your ignition module on the distributer. if not its the coil.

User Avatar

Very few trucks at that time had automatic transmission. So you can start a manual transmission by pushing it off. Turn on the ignition switch. Place the gear into 2nd gear. Depress the clutch. Push the truck to about 5 to 10 mph and release the clutch and the engine will start.

User Avatar

If you turn the ignition to the on position, and then press the interlock button, you don't have to press the clutch pedal down to start the truck.

User Avatar

Is the bike in neutral? Has any alarm system been deactivated? Is the battery charged?

User Avatar

More than likely because of a short. its probably a shorted ignition switch

User Avatar

If the Car didn't start with the key turning the ignition then the car was "hotwired" to turn the Car on.If the key did not start the car, how was it started.

User Avatar

low fuel presure. try priming it by turning ignition on and off several times.

User Avatar

The starter could be bad. Or the battery. The starter could be bad. Or the battery.

User Avatar

iveco truck just wont start . just parked up and unlaoded got back in on ignition lights and wont start


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.