Want this question answered?
The difference lies in the number of lenses that each microscope has. A compound microscope has 2 or more lenses, like those found in most science classrooms. A simple microscope uses only 1 lens.
The nose piece holds the odjective lense, rotates, and notes the positive stops for each lens.
The Magnifying Parts of the Microscope are the : - Eyepiece / Ocular Lens - Objective Lenses *High Power Objective *Low Power Objective *Scanner *Oil Immersion Objective
Manipulate a MicroscopeInstructions1Set up the microscope on a flat surface. Always carry the microscope using two hands if the microscope must be transported from one area to another. One hand should support the bottom while the other hand is holding the arm. Once in place, remove the any covers and plug in the microscope.2Position the slide onto the stage. Clip it into or under the slide holders. Turn on the light from the illuminator under the stage. Center the slide the best way possible without using any focusing knobs or the eyepiece.3Look through the eyepiece, keeping both eyes open to avoid eye strain, while using the course focus knob to bring the stage and slide closer to the objective, which is the lens that extends below the eyepiece, until the object can be seen through the eyepiece. Use the fine focus knob (which will also be on the side of the microscope) to bring the image into sharper focus.4Center the object being viewed. Change the iris diaphragm under the stage using the level to open and close the iris. Change the amount of light entering the specimen as needed. Changing the amount of light going through the slide may show additional details not seen at higher light levels.5Change to the 10X objective which is the next longest lens by rotating the lens pieces. The object should appear larger and only require using the fine focus knob to bring it into sharper detail. Use the iris diaphragm to change the amount of light entering the slide. Continue to the 40X objective and repeat. Each time the object will appear larger and you will be able to see less of the object at any one time while viewing.6Lower the stage and add one or two drops of immersion oil to the slide. Change the microscope to the 100X objective. Slowly raise the stage using the course focus until the objective is touching the oil. Use the fine focus knob to bring the object into sharp focus. Clean the slide and objective with lens tissue after use.7Return the stage to the lowest level. Change the objective back to the 4X lens. Unplug the machine and replace any covers. Carefully return the microscope using both hands to where it is stored.
Although the Lab Manual describes it, here it is... Iris Diaphragm: used to regulate the amount of light entering the lens system. Coarse-adjustment knob: used to raise or lower the body tube of the microscope. Fine-adjustment knob: used to bring specimen into sharp focus. Condenser: controls the maximum numerical aperture and to move the condenser itself. Mechanical stage control: used to adjust the slide vertically and/or horizontally to bring slide into central opening of the objective.
A low power objective in a microscope is a Small Lens with Low Magnifying Power. A microscope head with two eyepiece lenses, one for each eye. Generally this term is used in describing a high power (compound) microscope. With a low power microscope we say "stereo" head because, unlike the compound microscope, the stereo has a separate objective lens for each eyepiece lens, producing two independent paths of light, one for each eye. In the compound microscope with a binocular head, there are two eyepiece lenses but still only one objective lens and you will not get stereo vision. Hope this helps.
enumerate thedifferent parts of a compound microscope write and function of each
Jocky
The compound microscope consists of an arm to support base, lens to see through, stage to place the slides, illuminator for steady light and rack stop for adjustment. A dissecting microscope consists of diopter for adjustment, lens for viewing, focus knob for focusing on the subject and rotating objective turret for zoom control.
Allows each objective to be swing into position. ---Co0leTs24
The difference lies in the number of lenses that each microscope has. A compound microscope has 2 or more lenses, like those found in most science classrooms. A simple microscope uses only 1 lens.
Most microscopes have 4 to 5 lenses. The lenses are:The three Objects (which are the three things that you use to microscope)The lens that you you put your on.And the mirror lens.
The ocular lens are 10x magnification. Objective lens are 4x, 10x, 40x, 100x magnification. So once an objective lens is selected, the total magnification would be given by its product with the 10x magnification of the ocular lens. For example, if objective lens selected is 40x, total magnification would be: (10x)(40x)=400x total.
It is to change the objective of the lenses in the microscope
Multiply the Ocular strength by the Objective strength. In this case: 60x, 150x, 675x, 1455x
Multiply the Ocular strength by the Objective strength. In this case: 60x, 150x, 675x, 1455x
WordNet - Cite This Source - Share This objective lensnoun the lens or system of lenses in a telescope or microscope that is nearest the object being viewed [syn: objective]WordNet® 3.0, © 2006 by Princeton University. View results from: Dictionary | Thesaurus | En