Alternators
Saturn (car)
New Electrical Work
Modification of Old Electrical Work

What do you do if a wire grounds out after you hook the alternator back on to a 1993 Saturn?

567

Top Answer
User Avatar
Wiki User
Answered
2008-02-16 05:42:14
2008-02-16 05:42:14

Is the alternator a known good one? You could have a bad rectifier in your alternator causing a short to ground when it is installed.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Remove the wiring harness from the back of your 1993 VW Jetta alternator. Remove the three alternator retaining bolts. Remove the alternator belt. Reverse the process to install your new alternator.

the fuel guage in my 1993 Saturn goes wiggling back and forth. how do i fix this problem?

Either take the front right tire off or jack the car up and go in from the bottom.

Remove the belt from your 1993 Cadillac Deville alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.

Begin by removing the belt from your Mercedes-Benz alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.

On the 1995 Saturn SL1 The oil pressure sending unit is the sensor closest to the alternator. The unit is on the back of the block.

Disconnect the battery. Remove the alternator belt. Disconnect the wiring on the alternator, then unbolt and remove the unit. Bolt the new alternator in place and connect the wiring. Install the belt and connect the battery back up.

The oil pressure sending unit is located on the back of the block. it is the sensor located closest to the alternator.

No probes have come back from Saturn.

You have to take off the alternator to be able to reach the fan . After you should oiul the belt to slip on the fan very easy . Put the alternator back on and your ready to go .

from the back of the alternator to the dash to the battery

I have a 1993 dodge grand caravan, and have taken the alternator off of the bracket, but it will not fit down the back of the motorand under the fire wall. I have tried to remove the alternator bracket , but it looks as though it is trapped behind the tensioner pulley. I don't see how to remove the pulley bracket and don't know if this will work at all. What a crazy design! I hope someone out there can help.

the oil pressure switch is located on the back of the engine block closest to the alternator. it has a single Tan wire running to it, and a Grey connector.

How do I put the back seat bottom back in my 2002 Saturn L200? The Mechanic took it out and did not replace it. How do I put the back seat bottom back in my 2002 Saturn L200? The Mechanic took it out and did not replace it.

You will need to remove the alternator belt. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.

you can see it from the passenger side under the hood find the power steering pump at the back by the fire-wall you'll see the pulley that is attached to the steering pump, then look just to the right and straight down looks like a fan pulley that is your Alternator

ther is a tesionor pulley that releives pressure to the belt. it should take a 5/8 wrench

there are a lot of question about Saturn but, one is does Saturn have rings? I will let you respond to me back for the answer.

Remove the wiring harness from the back of your 1995 Chrysler LHS alternator. Remove the alternator belt. Remove the alternator retaining bolts. The alternator will come off and can be replaced with the new alternator.

Remove the alternator belt from your 1996 Ford Ranger alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.

The 1995 Infinity alternator can be replaced by removing the alternator belt. Removing the wiring harness from the back of the alternator. Removing the alternator retaining bolts. Put the new alternator on and reverse the process.

Disconnect the battery. Unplug the alternator and take the belts off. Unbolt the alternator, and bolt the new one in. Put the belts back on it. Plug it back in and reconnect the battery. Voila! You changed your own alternator!

It is under the alternator on the back of the engine. Just follow the belt down from the back of the alternator.

It is on the back of the engine between the starter and alternator It has one wire going to it. Threads into the block with a nig "housing" on it Careful the oil pressure switch is right beside it.

You can replace the alternator on your 1989 Mercury Cougar by removing the alternator belt. Disconnect the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.