answersLogoWhite

0

Without this, your distributor won't work. Without your distributor... :( Go to your distributor. On the outside of it you should see a plug with harness (?) feeding into the distributor. This is the beginning of your pickup coil "assembly". Take off your distributor cap. You'll see that "harness"/assembly feeds into the very top of your distributor, held by a "molded" grommet (on mine), then, it "coils" around the top and you'll see that it feeds (or plugs into) into some part of the distributor (again, you can only see this when your distributor cap is off). I'm basing all of this on my 84 CJ7. I have no clue if all distributors are the same. Good luck.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you change pickup coil on 1978 Chevy pickup?

u have to pull the whole distributer to change the pickup coil


Where do you put distributor pickup assembly?

The distributor pickup assembly is typically located inside the distributor housing, where it senses the position of the rotor. It is mounted near the reluctor wheel, which spins with the engine, allowing the pickup to generate a signal for the ignition system. In some modern engines, this assembly may be integrated into the ignition coil. Proper installation ensures accurate timing for ignition.


How voltage is induced in a permanent magnet pickup coil as the reluctor approaches alignment with the pickup coil.?

The Hall effect.


On an 86 Toyota truck what should the pickup coil resistance be?

Distributor pickup coil resistance 140-180 ohms.


How do you replace pick up coil on 02 650 Yamaha?

To replace the pickup coil on a 2002 Yamaha 650, first, disconnect the battery to ensure safety. Remove the side cover to access the stator assembly, then disconnect the wiring harness from the pickup coil. Unscrew and carefully remove the old pickup coil, then install the new one by reversing the process, ensuring all connections are secure before reassembling the side cover and reconnecting the battery. Remember to consult your service manual for specific torque specifications and installation details.


How to test pickup coil 1990 chevy pickup?

hey are located inside the distributor and function as the trigger for the ignition system to produce spark. The pickup coil monitors the rotation


What are the differences between a humbucker and a double coil pickup in terms of sound quality and performance?

A humbucker pickup has two coils that cancel out noise and produce a warmer, thicker sound with less feedback. A double coil pickup, also known as a single coil pickup, has one coil and produces a brighter, clearer sound but is more prone to interference and hum.


What are P90's on a guitar?

A type of pickup. Made by Gibson, they are a single-coil pickup.


How do you replace the evaporator coil in a 1985 S10 pickup?

To replace the evaporator coil in a 1985 S10 pickup, first, disconnect the vehicle's battery and drain the air conditioning system to remove refrigerant. Remove the dashboard and the heater assembly to access the evaporator coil, which is typically located inside the HVAC box. Disconnect the old coil's refrigerant lines, unbolt it from the housing, and replace it with the new coil. Reassemble the HVAC system, reconnect the refrigerant lines, and refill the AC system with refrigerant before testing for leaks.


How is voltage induced in the distributor pickup coil as the reluctor high point approaches alignment with the pickup coil?

The coil charges with electricity, and as the reluctor hits the high point, it releases all the energy at once.


Pick up coil location 2000 650 v star?

Pickup coil is located in the left side of the crankcase directly outside the stator assembly. The oil must be drained, the sidestand removed and the shift linkage swung away to remove the crankcase cover. To replace the coil, the seats and gas tank must also be removed to properly route the wires. Some later years have a single piece pickup coil and stator module that must be replaced together.


How do you change pickup coil on a 1988 GMC 2500 pick up?

Remove Distributor,remove drive gear,remove shaft,remove pickup coil.