0
It is a mitre saw that only angles one way.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What does double bevel mean for miter saw?
It means the blade can be tipped in two directions. Either left or right. A single bevel saw can only lean the blade in one direction. You can do the same cuts with a single bevel saw, but a dual bevel can save time and can make some cuts easier.
How do you cut a valley rafter with a compound miter saw?
You set the bevel on your saw to a 45 degree angle. Then set the angle on your saw base to the angle of your plumb cut.
Can the Miter and bevel settings on the saw easily make consistent repetitive cuts?
They should but still they demand care and a good "hand" to make consistent cuts.
What kind of cuts can you get on table saw?
Rip, cross, dado & "sink".Table saw cuts include rip cuts, crosscuts, miter box cuts and bevel cuts.A rip cut is a cut made parallel to the wood grain.A crosscut is generally at a fixed 90 degree angle.A miter cut involves a table saw with a miter gauge. A table saw with a miter gauge has one or two slots or grooves running from the front to the back of the table. These slots or grooves are used to position and guide the miter gauge or crosscut fence to set the miter cut at a precise angle. With this cut, the material being cut is angled versus the blade.Bevels are cut by changing the angle of the blade with respect to the surface of the wood on the table.
How do you get a replacement lower blade guard for your miter saw?
Try contacting the manufacturer of your miter saw. They may have available replacement parts.
Miter Saw Stand?
form_title= Miter Saw Stand form_header= Put safety first with a Miter saw stand. What size saw stand do you need?*= _ [50] Have you ever owned a saw stand before?*= () Yes () No Do you want the stand to be portable or stationary?*= {Portable, Stationary, Not Sure}
What are the domestic uses of a Slide Compound Miter Saw?
There are many domestic uses of a Slide Compound Miter Saw. The domestic uses, for the Slide Compound Miter Saw, include using it for woodwork or cutting through any sort of material.
How do I cut cove molding?
AnswerUse a miter box or a miter saw.First, some assumptions:A) The moulding used has a 45 degree "spring" or slope.B) the corner you are cutting, inside or outside is 90 degrees.There are 2 ways to do this, depending on whether you have a simple mitre saw, or one with compound mitre/bevel capability.1) Using a mitre saw ( no compound bevel capability):Place the "top" (ceiling) edge of the moulding closest to you, on the saw bed.Place the "bottom" edge on the fence of the saw.Position the molding at a 45 degree slope between the bed and the fence.The molding is now bridging the bed of the saw to the fence at 45 degrees.Set the saw mitre to 45 degrees and cut the moldingCut.For the mating piece, reverse the blade miter and bevel, and cut with the material pointing from from the opposite side of the blade.2) Using a compound mitre saw (compound miter & bevel capability):Place the back of the moulding flat on the bed of the saw.The "bottom" edge goes against the fenceThe "top" (ceiling) edge is closest to you.Set the saw miter to 35.3 degreesSet the blade tilt (bevel) to 30 degrees.Cut.For the mating piece, reverse the blade miter and bevel, and cut with the material pointing from from the opposite side of the blade.If the angle, or "spring" of the moulding is not 45 degrees ( 38 degree moulding is quite common, fro example), or: If the corner is not 90 degrees, then you will need a table to work with.These may be purchased here:http:/www.compoundmiter.com/chart.html#cr-mld-tableI also found free ones here:http://www.extremehowto.com/xh/article.asp?article_id=60354And, Remember to protect your fingers!Inside corners should be coped not mitered in good quality work. Butt one piece to the corner. Cut the other at 45*, which will give you a line along the face of the moulding. Using a coping saw (hence the name), cut along this line at a right angle to the length of the piece. Butt this second piece to the first to complete the joint. If the corner is obtuse then you will have to over-cut with the coping saw to achieve a tight fit. This method obviates an inside mitered corner opening when nailed up.
Who makes the best compound miter saw and stand for the money?
John's Tool Crib makes the best compound miter saw and stand for the money
WHAT IS A COMPOUND MITER SAW USED TO DO?
A compound miter saw can cut two angles at the same time. Very useful when cutting crown molding.
What is a sentence with the word miter?
A miter saw will help make our crown molding project almost easy.
What sizes does the Bosch Miter Saw come in?
The Bosch Miter Saw is available in two sizes. It is available in a 10 inch size or a 12 inch size. Saw stands are also available for this type of saw.
