0
HVAC Load Calculation is a formula used by a contractor salesmen that determines the proper tonnage size of heating and cooling systems to be installed in Residential or Commercial applications.
The formula is used to calculate the total cooling and heating BTU'S (British Thermal Units) for the proper values of determining the correct tonnage to be installed in HVAC applications. Tonnage is the size of the HVAC system.
Without this Load calculation the wrong tonnage could be installed and it causing to much humidity in the summer in cooling season and not enough heating in the winter season.
Also the HVAC system may never stop running to reach the proper temperature that the thermostat is set for. Thus causing high electricity out of pocket cost.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is mean by non-sinusoidal load?
A load that is not sinusoidally varying (i.e. resembling that of a graph of the function sin(x) or cos(x)). This means the load is not cycling or periodic so it does not repeat itself over and over - which is exactly what the graph of the trig function sin(x) demonstrates.
What does multiple burden mean?
Burden can mean different things, like a heavy load or a harship. Multiple burden means that there would be more than one load to carry, or more than one, probably many, hardships a person was experiencing.
What does the 95 y on your tire mean?
The number is the load rating. Common car tyres range from about 87 (small car, light load) to 97 (larger car, heavier load) but can go from 71 (345kg) - 110 (1060kg). The letter is the speed index. Y is currently the highest available, tested up to 300km/h. More common indices are H (210km/h) & V (240 km/h).
What is the formula for the ideal mechanical advantage of the pulley?
IMA of a pulley= the number of ropes supporting the load. An easier way is to count how many times the rope wraps around the wheel. :)
What are the first billion digits of pi?
The first 10 digits are 3.1415926535 and these are sufficient for all but the most rigorous calculations. There is a text file available at the related link that has the first billion (takes at least 35 seconds to load).The field size of this page cannot accommodate even the first 200,000 digits.
EDS?
HVAC Software, HVAC Load Calculation Software, Energy Design Systems, HVAC
Formula for btu load calulation?
1 BTU needed to raise or lower 1degree F of 1 lb water
How do you determine basic heat load for hvac?
ACCA Manual J is the industry standard.
What is brake horsepower in hvac systems?
Brake horsepower is the hvac motor horsepower before the motor hp is dropped due to a load. Indicated, gross and SAE are other ways to rate horsepower.
Which calulation will be performed first in a formula that does not contain parentheses?
i think exponents? remember, PEMDAS?
What is an internal heating load for HVAC fan coil unit?
The question is too vague, It depends on the Tonnage (BTU's) and or the Horsepower of the fan motor.
What is a vacuum resrvoir on a 1996 S-10 for?
To operate the HVAC (heating, ventilation and air conditioning) system while the engine is under load and not producing vacuum.
Why does the air condition stop blowing when you go up a hill?
You are losing vacuum from cracked/bad vacuum lines or the vacuum check valve for the HVAC controls is bad. When the engine is under load climbing that hill it does not produce enough vacuum to operate a leaky HVAC system.
What is Elite software used for?
Elite Software is the world's premier software developer for HVAC, electrical, plumbing, and fire protection design software. Over 30 programs are offered for such applications as HVAC load calculations, building energy analysis, HVAC duct and pipe sizing, plumbing & lighting design, fault current calculations, voltage drops, fuse and breaker coordination, and much more. Our HVAC software sets the standard for excellence and ease-of-use in the industry.
Why your hvac haye high suction pressurehigh discharge pressure?
Dirty condenser coils, high outdoor temp and heavy indoor load if coils are clean. Overcharge.
What is the difference between calulations and calulation?
Not come across either word before, except as misspellings for calculation(s).
Wiring schematic for blower on a 2004 Chevy venture?
HVAC Diagram 1 HVAC Diagram 2 HVAC Diagram 3 HVAC Diagram 4 HVAC Diagram 5 HVAC Diagram 7 HVAC Diagram 8 © 2009 ALLDATA LLC. All rights reserved
