0
An 'ideal' op-amp has infinite input impedance, and real ones that you can buy for a
nickel come pretty close. That means that the input impedance or "loading effect" of
an op-amp all by itself is nearly zero, and the loading effect of a circuit that you
build with an op-amp is completely determined by the components you choose to
connect to it. You design the circuit to load the previous stage in any way you want.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What are the three factors that effect the electrical parameters of a op-amp?
Supply voltage , temperature , frequency are factors that effect the electrical parameters of opamp
Why feedback is used in op-amp?
Feedback in used in an op-amp to limit and control the gain. An op-amp, by itself, has very high gain, often more than 100,000. (A theoretical op-amp has infinite gain.) The external feedback loop forms a divider, more correctly a bridge, that is maintained in balance by the op-amp, giving the desired real gain.
What is LM312T?
op-amp
How can an OP-AMP be nulled?
op-amp can be nulled using offset voltage about +/- 1.5 mv to offset pins
What is Op-Amp non inverting amplifier?
When the feedback of the output terminal of an Op-Amp is given to the non-inverting terminal [pin 3 for IC-741] of that Op-Amp , then , that circuit is called non-inverting amplifier using Op-Amp. This circuit is called non-inverting because the output signal of this circuit is in phase with the input signal.
Will loading effect occur in cascading of LR low pass and LR high pass filter?
Yes, you have to use an op-amp buffer to prevent the loading effect.
What is drift in op amps?
Drift is the effect of temperature on an operational amplifier (op-amp). Ideally you want zero drift (ie. op-amp is not affected by change in temperature), however this can never be practically achieved.
What is the effect of the op amp in the circuit?
So long as you remain with the range of the device (power supply rails less a volt or two), the output of an op-amp will go to what ever value is required to maintain the input stages (bridge) to remain the same. So, the effect on input voltage on output of an op-amp is dependent on the feedback circuit.
What are the three factors that effect the electrical parameters of a op-amp?
Supply voltage , temperature , frequency are factors that effect the electrical parameters of opamp
What happens when magnitude of Vcc and Vee of op-amp are different?
When the magnitude of Vcc and Vee of op-amp are different the op-amp produces waveforms equal in the size of each rail.
How an op amp differs from a basic amp?
A basic, single transistor amplifier differs from an op amp: 1. The op amp has more gain 2. The op amp may have higher input resistance (so it loads the circuit less) 3. The op amp may have a lower output resistance (so it can drive larger currents) 4. The op amp likely has a lower frequency response (due to the high gain, unless you provide some sort of feedback loop) 5. The op amp is ridiculously complex compared to a simple amplifier 6. The op amp will require a positive and negative voltage (may be unnecessary with a single transistor amplifier)
Which characteristics of Op-Amp is responsible for virtual ground?
The main parameter responsible for virtual ground of an Op-Amp is Input Impedance . Generally , for an Op-Amp it is very high . So , we can conclude that the characteristics of an Op-Amp responsible for virtual ground is high input impedance .
What is LM312T?
op-amp
Why feedback is used in op-amp?
Feedback in used in an op-amp to limit and control the gain. An op-amp, by itself, has very high gain, often more than 100,000. (A theoretical op-amp has infinite gain.) The external feedback loop forms a divider, more correctly a bridge, that is maintained in balance by the op-amp, giving the desired real gain.
How can an OP-AMP be nulled?
op-amp can be nulled using offset voltage about +/- 1.5 mv to offset pins
What is use of 8th pin in op-amp?
This may vary from one op-amp to another, consult the datasheet.
How can an op amp comparator circuit be used for converting sine to square wave?
The wording are confusing an op-amp is an op-amp a comparator is another animal. an op-amp can be used as square wave generator by overdriving it but the results are not desirable. However a comparator will be a switch on-off at the set level.
