0
What else can I help you with?
Will a 12 dc volt 8 amp power supply run a 12DC volt 9 amp motor?
Yes but only up to a load torque of 8/9 of the rated torque.
What is torque percent in electrical motor and unit of torque?
In SI, torque is measured in newton metres (N.m). The percentage torque varies according to the design and specifications of a motor.
What is the difference between max torque and breakdown torque of a electric motor?
Max torque and breakdown toarque are the same...,.the point at which a motor will stop/stall.
What is the output torque of a pneumatic motor directly related to?
The output torque of a pneumatic motor is directly related to the air pressure supplied to the motor and the size of the motor's displacement. Higher air pressure increases the force exerted by the motor's internal components, leading to greater torque. Additionally, a larger displacement allows for more air volume to act on the motor's pistons or vanes, enhancing torque output. Thus, both pressure and displacement play crucial roles in determining the motor's torque performance.
Which motor has a higher starting torque?
A series-wound commutator motor has the best starting torque because the torque is proportional to the square of the current, and the starting current is set by a current-limiting resistor which is switched out as the motor builds up speed.
Why is Dc series motor used to start at heavy load?
due to its high initial torque value. the DC series motor is a Constant power motor, equal to the RATED POWER if it has at rated value of the U and I. Angular velocity=Rated Power/Torque, so Torque =Rated Power/Angular Velocity thus, in the start the velocity is zero or near, so, the Torque is infinit or very higt
Why is dc series motor used to start heavy loads?
due to its high initial torque value. the DC series motor is a Constant power motor, equal to the RATED POWER if it has at rated value of the U and I. Angular velocity=Rated Power/Torque, so Torque =Rated Power/Angular Velocity thus, in the start the velocity is zero or near, so, the Torque is infinit or very higt
Full load torque of induction motor?
The full load torque of an induction motor is the maximum torque it can produce at its rated speed when operating at full load conditions. This torque is necessary to drive the load at the desired speed under normal operating conditions. It is an important parameter to consider when selecting a motor for a specific application.
How do you calculate hydraulic motor torque?
how to calculate hydraulic motor torque
Will a 12 dc volt 8 amp power supply run a 12DC volt 9 amp motor?
Yes but only up to a load torque of 8/9 of the rated torque.
What is the horespower of the 95 lt1?
Completely stock motor is rated 275hp and 325 ft lbs of torque at 2400 rpms
Can 3 phase induction motor start and run rated speed by 2 phase?
yes, It would run as long as the motor was not coupled to a load. Coupled to a load the motor would have no torque and would stall.
What is torque percent in electrical motor and unit of torque?
In SI, torque is measured in newton metres (N.m). The percentage torque varies according to the design and specifications of a motor.
How much horse power does a 93 trans am have?
IIRC, the motor for that year was the LT1, which was rated at 300 horsepower and 330 foot-pounds of torque.
What is reluctance torque?
torque of synchronous motor with out feild exitation
What is the difference between max torque and breakdown torque of a electric motor?
Max torque and breakdown toarque are the same...,.the point at which a motor will stop/stall.
How much load in tons can a 1200 hp dc motor take. is there any formula to calculate?
This question is not fully specified. A motor's maximum load is rated in torque. The pull-out torque also differs from the starting torque and rated torque. So to give an exact answer would rely on assumptions. Remember that torque equals weight (Newtons or Pounds) multipled by distance (metres or feet). This can give you the maximum weight than can be lifted when the radius of the pulley/gear mechanism is known. What may also help is knowing that power (hp) equals rotational speed multiplied by torque.
