0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Source to drain in FET is made of which material?
Semiconductor.
How jfet works?
A Jfet works by applying voltage to the drain of the jfet. A jfet will then conduct across from drain to source.
What is input impedance of fet amplifier?
Zin=Vds/Id [Vds=drain to source voltage ; Id = drain current]
How much signal voltage should be measured at the bypassed source of a common source amplifier?
the same amount as the drain
What are the different parasitic capacitances of NMOS transistors?
Parasitic capacitances form across every depletion region there's also a capacitance between the conductive leads to the terminals. For simplicity they are usually just lumped to each of the terminals of the transistor. Gate, Drain, Source and Substrate. If substrate is shorted to source creating typical 3 terminal representation then that half of those parasitic capacitances combine and Css (source-substrate) = 0. Cgd Cgs Cds (primarily from drain to substrate, not drain to source)
What type of doping have the drain and the source of a PMOS transistor?
PMOS - (drain + source) = p-type doping NMOS - (drain + source) = n-type doping :)
What is drain resistance?
drain resistane is basically the resistance offered by the drain terminal of the fet device.its the ratio of change in drain to source voltage to the change in drain current at a constant gate to source voltage.
What is the influence of gate voltage on drain source breakdown voltage in mos transistors?
Drain-to-source breakdown voltage (BVdss) should not change appreciably until the gate-to-source voltage (Vgs) approaches the device's threshold voltage (Vth). In that case, the drain to source voltage becomes the product of the drain-to-source current (Ids) and the device's on-state resistance (Rds-on) at the given Vgs.
Source to drain in FET is made of which material?
Semiconductor.
How jfet works?
A Jfet works by applying voltage to the drain of the jfet. A jfet will then conduct across from drain to source.
What is the verb of drainage?
The verb drain is the source of the noun drainage.
What is input impedance of fet amplifier?
Zin=Vds/Id [Vds=drain to source voltage ; Id = drain current]
How much signal voltage should be measured at the bypassed source of a common source amplifier?
the same amount as the drain
What are the rating of MOSFET?
The basic ratings are:ID, the highest average current (and IDmax, the highest peak current) that you are allowed to feed through the drain and source terminals, andVD, the maximum voltage that you are allowed to apply between drain and source.
WHAT IS MOS CAPACITOR?
it is a capacitor created with a cmos transistor where the source, body and gate are tied together to ground and the drain is tied to the source voltage.
The transfer characteristics of a JFET with external bias?
Transfer Characteristic of JFETThe transfer characteristic for a JFET can be determined experimentally, keeping drain-source voltage, VDSconstant and determining drain current, ID for various values of gate-source voltage, VGS. The circuit diagram is shown in fig. 9.7 (a). The curve is plotted between gate-source voltage, VGS and drain current, ID, as illustrated in fig. 9.8. It is similar to the transconductance characteristic of a vacuum tube or a transistor. It is observed that (i) Drain current decreases with the increase in negative gate-source bias(ii) Drain current, ID = IDSS when VGS = 0(iii)Drain current, ID = 0 when VGS = VD The transfer characteristic follows equation (9.1)The transfer characteristic can also be derived from the drain characteristic by noting values of drain current, ID corresponding to various values of gate-source voltage, VGS for a constant drain-source voltage and plotting them.It may be noted that a P-channel JFET operates in the same way and have the similar characteristics as an N-channel JFET except that channel carriers are holes instead of electrons and the polarities of VGS and VDSare reversed.
How fet is used as vvr?
FET AS A VOLTAGE -VARIABLE RESISTOR (VVR):FET is operated in the constant current portion of its output characteristics for the linear applications .In the region before pinch off , where Vds is small the drain to source resistance rd can be controlled by the bias voltage Vgs.The FET is useful as a voltage variable resistor (VVR) or Voltage Dependent resistor.In JFET the drain source conductance gd = Id/Vds for small values of Vds which may be expressed as gd = gdo [ 1-( VgsVp)1/2 ] where gdo is the value of drain conductance when the bias voltage Vgs is zero.The variation of the rd with vgs can be closely approximated by rd = ro / 1- KVgs ro - drain resistance at zero gate bias and K constant dependent upon FET type.Small signal FET drain resistance rd varies with applied gate voltage Vgs and FET act like a VARIABLE PASSIVE RESISTOR.Advantagesof JFETVery high input impedance order of 100 ohmOperation of JFET depends on the bulk material current carriers that do not cross junctionsNegative temperature coefficientsVery high power gainSmaller size longer life and high efficiencyAc drain resistance rd it is the ratio of change in drain - source voltage to the change in drain current at constant gate source voltageTransconductance it is the ratio of change in drain current to the change in gate source voltageat constant drain source voltageAmplification factor it is the ratio of change in drain source voltage to the change in gate source voltage at constant drain current.
